
Cube motherboard
willem-pennings/balancing-cube
A cube that balances itself in a corner or edge using reaction wheels

PCB/Electronic Files for LibreHealth-Lift
Librehealth Lift is an open-source printed circuit board by Mallo321123, from the Mallo321123/LibreHealth-Lift_PCB repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 97 × 67 mm with 18 parts on 52 nets, routed with 135 tracks and 2 vias.
It is built around the ESP32-S3-DEVKITC-1-N8. Its parts include 7 connectors, 3 ICs, 3 transistors, 1 capacitor and 1 resistor. It belongs with the ESP32 boards of this library.
PCB/Electronic Files for LibreHealth-Lift
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | Jumper_2_Bridged | PCM_Jumper_AKL:Jumper_P2.54mm_D1.2mm | JP1, JP2, JP3 |
| 3 | PMOS | Package_TO_SOT_SMD:TSOT-23 | Q1, Q2, Q3 |
| 3 | SPI | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1, J3, J4 |
| 1 | 22R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 3.3V | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J5 |
| 1 | C_Polarized | Capacitor_THT:CP_Radial_D8.0mm_P3.80mm | C1 |
| 1 | Display | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J7 |
| 1 | ESP32-S3-DevKitC | PCM_Espressif:ESP32-S3-DevKitC | U1 |
| 1 | GND | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J6 |
| 1 | SD card | modules:SD-Breakout | U3 |
| 1 | SPI-CS | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | ~ | modules:ISM330DLC | U2 |

willem-pennings/balancing-cube
A cube that balances itself in a corner or edge using reaction wheels

jazzmonger/Traeger-PID-Controller
Traeger Smoker/Grill Controller based on an

ohasanov-hbrw/tribit32-advanced
A tri-microcontroller, overengineered GameBoy Advance clone. More value was given to the controls and the exterior look, which is cool!



FIPATECH/CDFR26_PAMI
Open source firmware and PCB for a differential mobile robot (PAMI) based on ESP32-S3 - Coupe de France de Robotique

dnhutchins/ETC_Express_Reverse_Eng
The ultimate goal of this work is to develop an interface to use the control surface from a legacy ETC Express 24/48 lighting controller as a modern EOSNomad compatible programming and fader wing.

heckler/esphome-device-configs
Configuration definitions for local ESPHome files
It measures 97 × 67 mm and has 2 copper layers, 1.6 mm thick.
18 parts, built around the ESP32-S3-DEVKITC-1-N8. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Mallo321123/LibreHealth-Lift_PCB repository on GitHub, at the commit this page was made from: the board is dev-board-V1/Librehealth Lift.kicad_pcb and its schematic dev-board-V1/Librehealth Lift.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).