
Presplit 39key plate2
MachiaWorks/picobd
30% (close to 40%) keyboard using Raspberry Pi Pico.

30% (close to 40%) keyboard using Raspberry Pi Pico.
Presplit 39key is an open-source printed circuit board by MachiaWorks, from the MachiaWorks/picobd repository on GitHub, published under the MIT licence. It is a 2-layer board of 229.6 × 76.2 mm with 98 parts on 75 nets, routed with 422 tracks and 10 vias.
Its parts include 39 switches, 38 diodes and 1 IC. It belongs with the keyboards and input boards and the RP2040 boards of this library.
30% (close to 40%) keyboard using Raspberry Pi Pico. Picobd is an abbreviation of "Raspberry pi pico keyboard".

detail:
https://machiaworx.net/?p=1359
If you place an order or build a keyboard using these sets of files, please use them at your own risk. Even if damage occurs during construction, the author will not take any responsibility.
use "pcb.zip","plate.zip",and "bottom.zip" in "/gerber".
I usually order from JLCPCB in manufacturing.
under construction...
PRK firmware
https://github.com/picoruby/prk_firmware
KMK firmware
under construction...
Keyboard Layout Editor
http://www.keyboard-layout-editor.com/
Plate & Case Builder
KBD - for building keyboard libraries
https://github.com/foostan/kbd
su120-keyboard
https://github.com/e3w2q/su120-keyboard
KiCad-RP-Pico
| Qty | Value | Footprint | References |
|---|---|---|---|
| 38 | DIODE | kbd:D3_TH_SMD_v2 | D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +22 |
| 38 | Switch_SW_Push | kbd:CherryMX_1u | SW1, SW2, SW10, SW11, SW12, SW13, SW14, SW15, SW16, SW17, SW18, SW19, SW20, SW21, SW22, SW23 +22 |
| 9 | , , , , , , , , | ||
| 7 | footprint:M2_Hole | , , , , , , | |
| 4 | TestPoint_Pad_D1.0mm | TestPoint:TestPoint_Pad_D1.0mm | , q, q, r |
| 1 | Pico | MCU_RaspberryPi_and_Boards:RPi_Pico_SMD_TH | U1 |
| 1 | SW_Reset | kbd:ResetSW | SW41 |

MachiaWorks/picobd
30% (close to 40%) keyboard using Raspberry Pi Pico.

MachiaWorks/picobd
30% (close to 40%) keyboard using Raspberry Pi Pico.

pierrechevalier83/ferris
A low profile split keyboard designed to satisfy one single use case elegantly




PiTracLM/PiTrac
Launch monitor using low-cost raspberry pi and camera hardware to determine ball launch speed, angles and spin. See https://discord.gg/vGuyAAxXJH (permalink)


joshajohnson/Hub16
A macro pad with 16 keys, two rotary encoders, a four port USB hub, and plenty of LEDs!

c0pperdragon/C64-Video-Enhancement
Component video modification for the C64 8-bit computer
It measures 229.6 × 76.2 mm and has 2 copper layers, 1.6 mm thick.
98 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the MachiaWorks/picobd repository on GitHub, at the commit this page was made from: the board is rev1/presplit_39key.kicad_pcb and its schematic rev1/presplit_39key.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).