
Shield Gas Sensor Final
MOSH-Insa-Toulouse/Noize_Raynaud_GasSensor
KiCad sources for Gas Sensor

KiCad sources for Gas Sensor
MonPremierProjet is an open-source printed circuit board by MOSH-Insa-Toulouse, from the MOSH-Insa-Toulouse/Noize_Raynaud_GasSensor repository on GitHub. It is a 2-layer board with 20 parts on 56 nets, routed with 53 tracks and 0 vias.
Its parts include 8 resistors, 8 diodes, 2 connectors and 1 IC. It belongs with the sensors and measurement boards and the AVR (ATmega, ATtiny) boards of this library.
This repository contains the work produced during the course of Microcontroler and Open-Source Hardware (MOSH) of the 5th year Innovative Smart Systems (ISS) at INSA Toulouse. This work was produced by Alex Noize and Mathieu Raynaud.
The aim of this project was to design a complete PCB (Printed Circuit Board) implementing a double layer transimpedance amplificator assembly. This circuit is then used plugged to an Arduino board and a LoRa antenna to collect data from a gaz sensor and send it through a LoRa network.
The project is located here.
Let's first have a look to the electrical circuit:
On the center of the image, the double layer transimpedance circuit implements several functionalities:
We also have 3 other schemes on the picture which are:
Now, let's study the footprint generated with KiCad:
On the footprint above, we made the connections between all the needed pins of our board.
To be able to put our routes on only one face of the PCB, we had to add a ground layer on the entire surface of the PCB, so that we didn't need anymore to connect the ground-connected pins each others. This was also done for economical purposes.
Finally, we can see that two pairs of pins are still not connected on the footprint. In fact, these are two pairs of pins which are directly connected to the Arduino, and they have the same potential but they are already connected through the Arduino Uno.
Finally, here are the generated 3D views for our PCB:
The knowledge acquired during our courses allowed us to create with KiCad a PCB able to be plugged on an Arduino Uno, and to receive a gas sensor and a LoRa transceiver.
Now the next step is the print of the PCB and the creation of the gas sensor to implement the complete system.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | LED | LED_THT:LED_D5.0mm_FlatTop | D1, D2, D3, D4, D5, D6, D7, D8 |
| 8 | R | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1, R2, R3, R4, R5, R6, R7, R8 |
| 2 | Conn_01x06 | Connector_PinSocket_2.00mm:PinSocket_1x06_P2.00mm_Vertical | J1, J2 |
| 1 | Arduino_UNO_R2 | Module:Arduino_UNO_R2 | A1 |
| 1 | RN2483_Breakout | INSA_5ISS_LIBRARY1:Rn2483 Breakout | U1 |

MOSH-Insa-Toulouse/Noize_Raynaud_GasSensor
KiCad sources for Gas Sensor

MOSH-Insa-Toulouse/Noize_Raynaud_GasSensor
KiCad sources for Gas Sensor




atopile/atopile
Design circuit boards with code! ✨ Get software-like design reuse 🚀, validation, version control and collaboration in hardware; starting with electronics ⚡️

davidphilipbarr/Sweep
Sweep - a small promicro based keyboard inspired by the Ferris.

rusefi/rusefi
rusefi - GPL internal combustion engine control unit

hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

FreeYourStream/freedeck-hardware
all the stuff you need to build your own FreeDeck
20 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the MOSH-Insa-Toulouse/Noize_Raynaud_GasSensor repository on GitHub, at the commit this page was made from: the board is KiCad/MonPremierProjet/MonPremierProjet.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask MOSH-Insa-Toulouse before reusing the design.