4 layers86 × 33.6 mm
4 layers82.4 × 59.6 mm
Pixel click
Lee34667/PCB_Kicad_Projects1Creating a L9110 module using PCB techniques.
- Size
- 82.4 × 59.6 mm
- Copper layers
- 4
- Thickness
- 0.19 mm
- Parts
- 131
- Nets
- 120
- Pads
- 622
- Tracks, vias
- 842, 58
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 2 Jul 2024
- Updated
- 26 Mar 2025
Overview
Pixel click is an open-source printed circuit board by Lee34667, from the Lee34667/PCB_Kicad_Projects repository on GitHub. It is a 4-layer board of 82.4 × 59.6 mm with 131 parts on 120 nets, routed with 842 tracks and 58 vias.
It is built around the ESP32-S3, SN74LV1T34DBV and W25Q128JVSIQ, with the USBLC6-2P6, SK6805E-J and 2450AT18D0100E among its other parts. Its parts include 58 capacitors, 38 diodes, 17 resistors, 5 ICs and 5 switches. It belongs with the ESP32 boards of this library.
Main components
6
ESP32-S3
QFN-56-EP(7x7)-40℃~+105℃ -98.4dBm 150Mbps 2.412GHz~2.484GHz 2.4GHz 21dBm 340mA 3V~3.6V 88mA SPI、USB、UART、ADC、I2C、I2S、PWM WiFi transceiver QFN-56-EP(7x7) RF Transceiver ICs ROHSEspressif SystemsRF Transceiver ICs
SN74LV1T34DBV
SOT-23-5-40℃~+125℃ 1 1 1.6V~5.5V 10uA 5.5ns@5V,15pF 74LV 8mA 8mA Level shifting Push-pull Unidirectional SOT-23-5 Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsBuffers, Drivers, Receivers, Transceivers
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
USBLC6-2P6
SOT-666-6-40℃~+125℃ 150nA 17V 2 3.5pF 5.25V 5A@8/20us 6V ESD IEC 61000-4-2 Unidirectional SOT-666-6 ESD and Surge Protection (TVS/ESD) ROHSSTMicroelectronicsESD And Surge Protection (TVS/ESD)
SK6805E-J
SMD,5.4x5mm-40℃~+85℃ 0.5mA 1.6mm 100mcd~200mcd 100ns 120° 1kHz 2000V 3.7V~5.5V 385mcd~697.5mcd 460nm~470nm 5.4mm 50ns 520nm~535nm 5mm 620nm~625nm 800Kbit/s 80mcd~160mcd 80ns Built-in power-on reset circuit Semi-transparent lens SMD,5.4x5mm RGB LEDs(Built-in IC) ROHSOPSCO OptoelectronicsRGB LEDs(Built-In IC)
2450AT18D0100E
SMD-4P,3.2x1.6mm-40℃~+125℃ 1.2mm 1.5dBi 1.6mm 100MHz 2.4GHz 2W 3.2mm 50Ω Patch Antenna SMD-4P,3.2x1.6mm Antennas ROHSJohanson DielectricsAntennas
README
README.mdContains some the PCB projects I have done using KiCad. Most of this boards have been used in the industries and research work.
Parts
131| Qty | Value | Footprint | References |
|---|---|---|---|
| 44 | 0.1uF | Capacitor_SMD:C_0201_0603Metric | C1, C2, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23 +28 |
| 36 | SK6805 | LED_SMD:LED_SK6812_PLCC4_5.0x5.0mm_P3.2mm | D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +20 |
| 7 | 1uF | Capacitor_SMD:C_0201_0603Metric | C37, C42, C43, C46, C51, C52, C58 |
| 5 | 0 | Resistor_SMD:R_0201_0603Metric | R1, R2, R3, R4, R5 |
| 5 | 10K | Resistor_SMD:R_0201_0603Metric | R8, R9, R10, R11, R12 |
| 5 | 5K1 | Resistor_SMD:R_0201_0603Metric | R6, R7, R14, R16, R17 |
| 2 | NC | Capacitor_SMD:C_0201_0603Metric | C38, C39 |
| 1 | 10nF | Capacitor_SMD:C_0201_0603Metric | C56 |
| 1 | 10uF | Capacitor_SMD:C_0201_0603Metric | C50 |
| 1 | 2.2uF | Capacitor_SMD:C_0201_0603Metric | C47 |
| 1 | 2.4nH | Inductor_SMD:L_0201_0603Metric | L1 |
| 1 | 2.4pF | Capacitor_SMD:C_0201_0603Metric | C40 |
| 1 | 2.7pF | Capacitor_SMD:C_0201_0603Metric | C41 |
| 1 | 22 | Resistor_SMD:R_0201_0603Metric | R13 |
| 1 | 2450AT18D0100E | ANT1:DFN320X160X120-4RN | ANT1 |
| 1 | 2nH | Inductor_SMD:L_0201_0603Metric | L2 |
| 1 | 5k1 | Resistor_SMD:R_0201_0603Metric | R15 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_1.27mm:PinHeader_1x03_P1.27mm_Vertical | J2 |
| 1 | Crystal_GND24_Small | Crystal_Oscillator:XTAL_ECS-400-10-37B2-CKY-TR | Y1 |
| 1 | ESP32-S3 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP4x4mm | U1 |
| 1 | GREEN | LED_SMD:LED_0201_0603Metric | D38 |
| 1 | NetTie_2 | NetTie:NetTie-2_SMD_Pad0.5mm | NT1 |
| 1 | RED | LED_SMD:LED_0201_0603Metric | D37 |
| 1 | SN74LV1T34DBV | Package_TO_SOT_SMD:SOT-23-5 | U5 |
| 1 | TLV76733DRVx | Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm_ThermalVias | U4 |
| 1 | TestPoint | TestPoint:TestPoint_Bridge_Pitch2.0mm_Drill0.7mm | TP1 |
| 1 | USBLC6-2P6 | Package_TO_SOT_SMD:SOT-666 | U2 |
| 1 | USB_C_Receptacle | Connector_USB:USB_C_Receptacle_Amphenol_12401548E4-2A | J1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U3 |
| 1 | btn1 | Button_Switch_THT:SW_PUSH_6mm_H4.3mm | SW5 |
| 1 | btn2 | Button_Switch_THT:SW_PUSH_6mm_H4.3mm | SW3 |
| 1 | btn3 | Button_Switch_THT:SW_PUSH_6mm_H4.3mm | SW2 |
| 1 | btn4 | Button_Switch_THT:SW_PUSH_6mm_H4.3mm | SW1 |
| 1 | btn5 | Button_Switch_THT:SW_PUSH_6mm_H4.3mm | SW4 |
More from Lee34667/PCB_Kicad_Projects
12- 4 layers67.8 × 70.6 mm
- 2 layers22.5 × 110.8 mm
- 2 layers79 × 78 mm
Internal Resistance Meter
Lee34667/PCB_Kicad_Projects
Creating a L9110 module using PCB techniques.
29 parts1 - 4 layers68.6 × 86.4 mm
Solar Power Regulator PCB
Lee34667/PCB_Kicad_Projects
Creating a L9110 module using PCB techniques.
27 parts1 - 2 layers74.7 × 40.1 mm
RS485 Fire panel interface
Lee34667/PCB_Kicad_Projects
Creating a L9110 module using PCB techniques.
26 parts1 - 2 layers76.8 × 32.8 mm
- 8 layers89.9 × 116.8 mm
Two phase bipolar stepper motor
Lee34667/PCB_Kicad_Projects
Creating a L9110 module using PCB techniques.
21 parts1 - 4 layers24 × 38 mm
- 4 layers50.6 × 35.3 mm
- 4 layers52.3 × 29.2 mm
Multipurpose FM Transmitter
Lee34667/PCB_Kicad_Projects
Creating a L9110 module using PCB techniques.
18 parts1 - 2 layers41.1 × 27.9 mm
Similar boards
- 2 layers
- 4 layers32.2 × 34.1 mm
- 4 layers53.7 × 46.9 mm
- 4 layers48.8 × 46.3 mm
- 4 layers86.4 × 50.8 mm
LoRa device
indoor-industry/Mercurio-RevB
A project for a functioning handheld LoRa+GPS radio device
168 partsGPL-3.0 - 4 layers81.2 × 81.2 mm
- 6 layers172 × 100 mm
- 4 layers36 × 64 mm
Questions
How big is the Pixel click PCB?
It measures 82.4 × 59.6 mm and has 4 copper layers, 0.19 mm thick.
What parts does the Pixel click use?
131 parts, built around the ESP32-S3, SN74LV1T34DBV, W25Q128JVSIQ and USBLC6-2P6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pixel click KiCad files?
From the Lee34667/PCB_Kicad_Projects repository on GitHub, at the commit this page was made from: the board is Pixel_click/pixel_click.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pixel click design in my own project?
Its repository states no licence, so its author keeps all rights: ask Lee34667 before reusing the design.