
Temperature Tire Sensor
KozaMateusz/TireTemperatureSensor
TTS (Tire Temperature Sensor) is a PCB designed to measure the temperature quickly, at a distance, and without the need to touch the wheels.

TTS (Tire Temperature Sensor) is a PCB designed to measure the temperature quickly, at a distance, and without the need to touch the wheels.
TireTempSensor v2.0 is an open-source printed circuit board by KozaMateusz, from the KozaMateusz/tire_temperature_sensor repository on GitHub. It is a 4-layer board of 27 × 54 mm with 57 parts on 79 nets, routed with 263 tracks and 79 vias.
It is built around the STM32L4P5RET6, SN65HVD232D and MAX15462AATA+T, with the MLX90621ESF-BAB-000-SP, MIC5306-2.6YD5-TR and FQT3P20TF among its other parts. Its parts include 16 capacitors, 11 resistors, 6 diodes, 5 ICs and 2 connectors. It belongs with the STM32 boards of this library.
TTS (Tire Temperature Sensor) is a PCB designed to measure temperature quickly, at a distance, and without the need to touch the wheels. The 4x16 pixel IR camera is used to obtain the data. It communicates with the STM microprocessor via the I2C protocol. Data is then averaged out to a 1x8 array of unsigned ints and sent with the CAN Transceiver to the car’s CAN network. This array can be then read off of the telemetry system implemented in the PM-08 racing car.
While driving, a tire heats up. Heat dissipates differently across its surface and its rate changes depending on many factors (E.g. weather conditions or reoccurring acceleration). As a tire has its maximal temperature, exceeding this value may weaken its structural strength and cause its destruction in the worst-case scenario. This IR Camera PCB makes it possible to monitor a tire across its whole surface and prevent any damage associated with the temperature. As TTS monitors every wheel out of 4, our crew can easily detect if tires wear unevenly or excessively. Tire temperature patterns inform whether the car is properly calibrated, as the out-of-tune suspension causes tires to heat up significantly faster. This may result in grip loss in these areas.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100n | Capacitor_SMD:C_0603_1608Metric | C2, C3, C4, C5, C6, C7, C11, C14, C15, C17 |
| 5 | 1k5 | Resistor_SMD:R_0603_1608Metric | R4, R7, R8, R9, R10 |
| 4 | 60R@100MHz | Inductor_SMD:L_0603_1608Metric | FB1, FB2, FB3, FB4 |
| 4 | Mounting_Pad | MountingHole:MountingHole_2.7mm_M2.5_ISO14580_Pad | H1, H2, H3, H4 |
| 2 | 1u | Capacitor_SMD:C_0603_1608Metric | C12, C13 |
| 2 | 4k7 | Resistor_SMD:R_0603_1608Metric | R5, R6 |
| 2 | 8p | Capacitor_SMD:C_0603_1608Metric | C9, C10 |
| 2 | RED | Diode_SMD:D_0603_1608Metric | D2, D6 |
| 2 | YELLOW | Diode_SMD:D_0603_1608Metric | D3, D4 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 10u | Capacitor_SMD:C_1206_3216Metric | C16 |
| 1 | 16MGHz | Crystal:Crystal_SMD_SeikoEpson_TSX3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 200mA | Fuse:Fuse_1210_3225Metric | F1 |
| 1 | 33μH | Inductor_SMD:L_Vishay_IFSC-1515AH_4x4x1.8mm | L1 |
| 1 | 47 | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 4u7 | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | CAN_01x04 | Connector_Wire:SolderWire-0.1sqmm_1x04_P3.6mm_D0.4mm_OD1mm_Relief | J2 |
| 1 | FQT3P20TF | Mosfet:SOT-223-4-NFET | Q1 |
| 1 | GREEN | Diode_SMD:D_0603_1608Metric | D5 |
| 1 | LOGO | mylogo:logo | G*** |
| 1 | LOGO | logo:logo_3mm_FMask | G*** |
| 1 | LOGO | logo:logo_3mm_FCu | G*** |
| 1 | MAX15462AATA+ | Package_DFN_QFN:TDFN-8-1EP_2x2mm_P0.5mm_EP0.8x1.2mm | IC1 |
| 1 | MIC5306-2.6YD5-TR | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | MLX90621ESF-BAB-000-SP | IRSensor:MLX90621ESFBAB000SP | IC2 |
| 1 | PESD2CAN,215 | Package_TO_SOT_SMD:SOT-23 | D1 |
| 1 | RESET | Button:PTS815SJK250SMTRLFS | SW1 |
| 1 | SN65HVD232 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | STM32L4P5RET6 | Package_QFP:LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | SWD_01x06 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP1 |

KozaMateusz/TireTemperatureSensor
TTS (Tire Temperature Sensor) is a PCB designed to measure the temperature quickly, at a distance, and without the need to touch the wheels.

MoreThanRobotsFR/MTR_Tiny_MD
This Arduino project utilizes SimpleFOC library for sensor-based brushless motor control with a DRV8316 driver. It also incorporates an Adafruit NeoPixel for visual feedback.


PUT-Motorsport/PUTM_DV_ASB
Autonomus Brake System PCB and Software for PM07


PUT-Motorsport/PUTM_EV_STEERING_WHEEL_2022
An overview of how I see this thing working:


It measures 27 × 54 mm and has 4 copper layers, 4.69 mm thick.
57 parts, built around the STM32L4P5RET6, SN65HVD232D, MAX15462AATA+T and MLX90621ESF-BAB-000-SP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the KozaMateusz/tire_temperature_sensor repository on GitHub, at the commit this page was made from: the board is hardware/TireTempSensor_v2.0/TireTempSensor_v2.0.kicad_pcb and its schematic hardware/TireTempSensor_v2.0/CAN.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask KozaMateusz before reusing the design.