
Hotplate
Keyaan-07/Hotplate
Check out the Project's files on KiCanvas(PCB and Heating element) and Onshape!

Check out the Project's files on KiCanvas(PCB and Heating element) and Onshape!
HeatingElement is an open-source printed circuit board by Keyaan-07, from the Keyaan-07/Hotplate repository on GitHub, published under the MIT licence. It is a 2-layer board of 100 × 100 mm with 10 parts on 3 nets, routed with 1,133 tracks and 0 vias.
Its parts include 4 connectors and 1 resistor.
An open-source hotplate designed to take power from USB type-C and then be configured and controlled over Wi-Fi. It uses the ESP32-C3 microcontroller, along with 16MB of storage. There are two terminal blocks to connect with the heating element and it's temperature sensor. There is short circuit protection along with accurate current measurement on the power lines. The control frequency is 10KHz for the heating element. The heating element can be mounted on standoffs so as to not heat the surface below it.
Check out the Project's files on KiCanvas(PCB and Heating element) and Onshape!
Features:





wiring diagram between two parts:

I really wanted to build a custom hotplate so that i could make my own PCBs with ease and not struggle! The heating element is made up of an aluminium PCB so that there is good thermal conductivity.
I dont think i will be able to do the firmware unless and until i have the project in hand, because this requires proper PID tuning to just get the temperature right, and also it needs to be adjusted for errors in temperature measurement and power control!
Licensed under the MIT license.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | Conn_01x01_Pin | TestPoint:TestPoint_Pad_2.0x2.0mm | J3, J4 |
| 2 | Conn_01x01_Pin | TestPoint:TestPoint_Pad_4.0x4.0mm | J1, J2 |
| 1 | NTC | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1 |
The 5 most common of 10 parts.

Keyaan-07/Hotplate
Check out the Project's files on KiCanvas(PCB and Heating element) and Onshape!

gusmanb/logicanalyzer
24 channel, 100Msps logic analyzer hardware and software

byrantech/laptop
anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

joeycastillo/Sensor-Watch
A board replacement for the classic Casio F-91W wristwatch


OLIMEX/OLINUXINO
OLINUXINO is Open Source / Open Hardware, low cost from EUR 24 Linux Industrial grade Single Board Computer capable to operate -25+85C

rusefi/rusefi
rusefi - GPL internal combustion engine control unit

VoronDesign/Voron-Hardware
Cool Hardware designed by the Voron Design group

hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI
It measures 100 × 100 mm and has 2 copper layers, 1.6 mm thick.
10 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Keyaan-07/Hotplate repository on GitHub, at the commit this page was made from: the board is HeatingElement/HeatingElement.kicad_pcb and its schematic HeatingElement/HeatingElement.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).