4 layers69.2 × 57.8 mm
4 layers76.8 × 43.7 mm
Booth pcb
Ken-Takei101011/Personal_ProjectsCollection of my projects
- Size
- 76.8 × 43.7 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 53
- Nets
- 51
- Pads
- 207
- Tracks, vias
- 295, 90
- Pours
- 11
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 21 Aug 2026
- Updated
- 11 Oct 2026
Overview
Booth pcb is an open-source printed circuit board by Ken-Takei101011, from the Ken-Takei101011/Personal_Projects repository on GitHub. It is a 4-layer board of 76.8 × 43.7 mm with 53 parts on 51 nets, routed with 295 tracks and 90 vias.
It is built around the ESP32-S3-WROOM-1-N8, 24LC00/P and SUL6001S5-33. Its parts include 18 resistors, 13 capacitors, 7 connectors, 5 ICs and 2 diodes. It belongs with the ESP32 boards of this library.
Main components
3
ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi Modules
24LC00/P
PDIP-80℃~+70℃ 128bit 2.5V~5.5V 400kHz 4ms I2C PDIP-8 EEPROM ROHSMicrochip TechnologyEEPROM
SUL6001S5-33
SOT-23-5-40℃~+85℃@(Ta) 1 10uVrms 150mV@(1A) 3.3V 5.5V 500mA、1A 85dB@(1kHz) 85uA Fixed Positive Under Voltage Lockout、Over Current Protection、Over Temperature Protection、Soft Start、Enable SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSuntekVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdPersonal_Projects
Collection of projects I've worked on for my coursework, society work and personal stuff.
Additional Information:
-The WIFI router is incomplete.
-The component identifier is a project from ELEC3106. This is the version with design revisions after the final version was submitted and had issues.Parts
53| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 100n | Capacitor_SMD:C_0402_1005Metric | C5, C6, C7, C8, C9, C10, C11, C12, C15 |
| 8 | 10k | Resistor_SMD:R_0402_1005Metric | R1, R2, R3, R4, R5, R6, R7, R8 |
| 8 | SW_Push | Button_Switch_SMD:SW_SPST_TS-1088-xR025 | BOOT1, BOOT2, CONFIRM1, DOWN1, RST1, UNDO1, UP1, VOTE1 |
| 6 | 5.1k | Resistor_SMD:R_0402_1005Metric | R9, R10, R11, R12, R13, R14 |
| 4 | 1u | Capacitor_SMD:C_0603_1608Metric | C1, C2, C4, C14 |
| 3 | 24LC00 | Package_SO:SOP-8_3.76x4.96mm_P1.27mm | U4, U5, U6 |
| 2 | 22R | Resistor_SMD:R_0402_1005Metric | R17, R18 |
| 2 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J6, J7 |
| 1 | 1.5k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R15 |
| 1 | 150 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R16 |
| 1 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | Conn_01x10_Pin | Connector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_Vertical | J5 |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1 | U1 |
| 1 | GRN | LED_THT:LED_D4.0mm | D1 |
| 1 | JTAG | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | RED | LED_THT:LED_D4.0mm | D2 |
| 1 | SUL6001S5-33 | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01A | J1 |
More from Ken-Takei101011/Personal_Projects
2- 2 layers140 × 50 mm
Similar boards
- 4 layers63.9 × 40.2 mm
- 4 layers100 × 77 mm
- 4 layers35 × 16 mm
- 2 layers14.5 × 8.4 mm
Project soic8-stemmaqt mod
fgervais/project-soic8-stemmaqt-mod
Console modchip style flexpcb to add a Stemma QT connector on an SOIC-8 EEPROM
2 parts18 - 4 layers66 × 61 mm
- 2 layers115 × 70.6 mm
- 2 layers83.1 × 92.5 mm
- 2 layers14 × 11.4 mm
Questions
How big is the Booth pcb PCB?
It measures 76.8 × 43.7 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Booth pcb use?
53 parts, built around the ESP32-S3-WROOM-1-N8, 24LC00/P and SUL6001S5-33. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Booth pcb KiCad files?
From the Ken-Takei101011/Personal_Projects repository on GitHub, at the commit this page was made from: the board is ELEC3117_Project/booth_pcb/booth_pcb.kicad_pcb and its schematic ECG/ECG.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Booth pcb design in my own project?
Its repository states no licence, so its author keeps all rights: ask Ken-Takei101011 before reusing the design.