Skip to the content
2 layers35.9 × 35.9 mmProject1, the printed circuit board in 3D

For this project, we design a 12V AC to DC Converter using KiCad for schematic and PCB design. The circuit includes a transformer, full-wave rectifier, smoothing capacitor, voltage regulator, and LED indicator.

Size
35.9 × 35.9 mm
Copper layers
2
Thickness
1.6 mm
Parts
12
Nets
5
Pads
20
Tracks, vias
35, 0
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
1 Apr 2025
Updated
1 Apr 2025

Overview

Project1 is an open-source printed circuit board by KAMAKHYA022, from the KAMAKHYA022/PCB_DESIGN repository on GitHub. It is a 2-layer board of 35.9 × 35.9 mm with 12 parts on 5 nets, routed with 35 tracks and 0 vias.

Its parts include 5 diodes, 2 connectors, 1 capacitor and 1 resistor.

README

PROJECT1/README.md

Designing a 12V AC to DC Converter

For this project, we design a 12V AC to DC Converter using KiCad for schematic and PCB design. The circuit includes a transformer, full-wave rectifier, smoothing capacitor, voltage regulator, and LED indicator.

Components Used:

Transformer (X1) – Steps down 220V AC to 12V AC.

Bridge Rectifier (D1-D4, 1N4007 diodes) – Converts AC to pulsating DC.

Capacitor (C1, 1000µF) – Smooths the pulsating DC.

Voltage Regulator (U1, 7812 IC) – Provides a steady 12V DC output.

Resistors (R1, R2) – Current limiting resistors for circuit protection.

LED Indicator (D5) – Shows power status.

5. PCB Design in KiCad

The schematic is designed in KiCad, ensuring correct component placement and PCB layout. The PCB layout is optimized to minimize noise and improve efficiency.

Designing a 12V AC to DC Converter

Schematic Design in KiCad

Schematic Design

PCB Layout

PCB Layout

PCB 3D View

PCB 3D View

Simulation in Proteus

Proteus Simulation

6. Simulation in Proteus

To verify circuit functionality before manufacturing, the schematic is simulated in Proteus:

Transformer steps down 220V AC to 12V AC.

Bridge rectifier converts AC to DC.

Capacitor smooths the DC voltage.

IC 7812 ensures a regulated 12V DC output.

LED indicates circuit operation.

7. Why These Components Were Chosen?

7812 Voltage Regulator – Provides a steady 12V DC output with overvoltage protection.

1000µF Capacitor – Smooths rectified DC to reduce ripple.

10Ω Resistor (R2) – Helps with voltage stabilization.

2.2kΩ Resistor (R1) with LED – Limits current to the LED for indicating circuit operation.

8. Conclusion

This AC to DC converter provides a regulated 12V DC output from 220V AC input. The design ensures efficiency and reliability for powering various electronics. The project demonstrates PCB design, simulation, and implementation of a real-world power supply circuit.

Future Improvements:

Adding a heat sink to the 7812 regulator for better thermal management.

Designing a dual-output version for 5V and 12V DC supplies.

Implementing a switching regulator for better efficiency.

Parts

12
QtyValueFootprintReferences
41N4007Diode_THT:D_DO-41_SOD81_P10.16mm_HorizontalD1, D2, D3, D4
2Screw_Terminal_01x02TerminalBlock:TerminalBlock_bornier-2_P5.08mmJ1, J2
11000uFCapacitor_THT:C_Radial_D8.0mm_H11.5mm_P3.50mmC1
12.2KResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR2
1LEDLED_THT:LED_D5.0mmD5
1RResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal10K

The 10 most common of 12 parts.

Similar boards

  • 2 layersNrf bga, the printed circuit board in 3D

    Nrf bga

    github-linguist/linguist

    Language Savant. If your repository's language is being reported incorrectly, send us a pull request!

    12 parts14kMIT
  • 2 layers66.9 × 74.5 mmDeskHop, the printed circuit board in 3D

    DeskHop

    hrvach/deskhop

    Fast Desktop Switching Device

    12 parts7.9kGPL-3.0
  • 2 layers40 × 15 mmSensors, the printed circuit board in 3D

    Sensors

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    12 parts3kApache-2.0
  • 2 layers42.7 × 56.5 mmTle6240 driver, the printed circuit board in 3D

    Tle6240 driver

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    12 parts1.2k
  • 2 layers49 × 25 mm5v boost regulator, the printed circuit board in 3D

    5v boost regulator

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    12 parts915
  • 2 layers28.3 × 10.3 mmTap Photosensor PCB, the printed circuit board in 3D

    Tap Photosensor PCB

    VoronDesign/Voron-Tap

    Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Tap offers many advantages:

    12 parts716GPL-3.0
  • 2 layers25.4 × 70.4 mmTpmsniffer, the printed circuit board in 3D

    Tpmsniffer

    stacksmashing/pico-tpmsniffer

    A simple, very experimental TPM sniffer for LPC bus

    12 parts696

Questions

How big is the Project1 PCB?

It measures 35.9 × 35.9 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Project1 use?

12 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Project1 KiCad files?

From the KAMAKHYA022/PCB_DESIGN repository on GitHub, at the commit this page was made from: the board is PROJECT1/project1.kicad_pcb and its schematic PROJECT1/project1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Project1 design in my own project?

Its repository states no licence, so its author keeps all rights: ask KAMAKHYA022 before reusing the design.