Skip to the content
4 layers30.9 × 30.9 mmMIPI Switch V1.1, the printed circuit board in 3D

2-Camera Input MIPI Switch for Caddx Vista/DJI FPV V1/Runcam Link systems

Size
30.9 × 30.9 mm
Copper layers
4
Thickness
1.58 mm
Parts
15
Nets
71
Pads
146
Tracks, vias
773, 87
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
17 Aug 2024
Updated
30 Aug 2024

Overview

MIPI Switch V1.1 is an open-source printed circuit board by JoshG20, from the JoshG20/DJI-MIPI-Switch repository on GitHub, published under the CC0-1.0 licence. It is a 4-layer board of 30.9 × 30.9 mm with 15 parts on 71 nets, routed with 773 tracks and 87 vias.

It is built around the PI3WVR646GEEX. Its parts include 3 connectors, 2 resistors and 2 ICs.

Main components

1

README

README.md

DJI-MIPI-Switch

2-Camera Input MIPI Switch for Caddx Vista/DJI Air Unit/Runcam Link systems

V1.0: Initial Revision (INACTIVE)

image

  • The MIPI Switch has 2 MIPI D-PHY CSI inputs and 1 output, all using the DF56C-26P-0.3V(51) connector standard to the 26P DJI FPV system.
  • Switching is performed by the PI3WVR646GEEX analog multiplexer, which is the only device in the video signal path.
  • Routing is all length and impedence matched within each connector path. The 3 different connectors have different trace lenghts but this does not matter since each camera just sees a slightly longer or shorter total cable length.
  • The selection between A and B cameras is controlled by a Pololu RCS01B, which provides a user adjustable PWM threshhold.
  • This PCB has 25.5 x 25.5mm mounting holes to match the Caddx Vista and Runcam Link VTX.
  • Note1: This board does not pass through the I2C pins, which means cameras that require configuration will not work. Only 60fps cameras are supported.
  • Note2: This board is now INACTIVE. Pinout is incorrect.

V1.1: Fixes V1.0 issues (FUNCTIONAL, SEE NOTE 2)

image image

  • Fixed incorrect assumption that the DJI MIPI Coaxial Cable uses a 1-1 pin configuration. This means that pin 1 on the VTX footprint connects to pin 1 on the Camera. In reality, the cable is a 1-n or 1-26 configuration, which flips the pin numbering on one end. VTX-CAM = one flip, so VTX-PCB-CAM needs 3 to match. Therefore V1.1 has mirrored connector pinouts on the camera output connectors, leading to the correct orientation at all stages.
  • Improved the silkscreen labeling on the board, including marking the orientation of the PWM input
  • Added 20 x 20 mm mounting holes for flexibility
  • Note1: Do not use the pinout in this schematic, it has the MIPI lanes in the wrong order and polarity. It does not affect the function of this board, but only because this chip has interchangeable lanes.
  • Note2: This board works, however it does have a bug when switching back and forth rapidly (>1Hz). This crashes the VTX until power cycle.

V2.0: Integrated PWM reading (TBD)

  • Size TBD
  • Fixed MIPI lane order and polarity on the connectors.
  • Replaces 2.54mm pin header with smaller but still common JST SH1.0
  • Replaces Pololu RCS01B with integrated PWM reading circuit TBD
  • Blocks rapid switching via TBD
  • Stretch goal: I2C handling

Current Pinout Reference:

DJI MIPI Pinout

Parts

15
QtyValueFootprintReferences
8MountingHole_PadMountingHole:MountingHole_2.2mm_M2_PadH1, H2, H3, H4, H5, H6, H7, H8
3DF56C-26S-0.3V_51_DF56C-26S-0.3V_51:DF56C26S03V51J1, J2, J3
251kResistor_SMD:R_0402_1005MetricR1, R2
1PI3WVR646GEEXPI3WVR646GEEX:PI3WVR646GEEX_1IC1
1~RCS01B:RCS01B_PinHeader_2x04_P2.54mm_VerticalIC2

More from JoshG20/DJI-MIPI-Switch

1
  • 4 layers30.9 × 30.9 mmMIPI Switch V1.0, the printed circuit board in 3D

    MIPI Switch V1.0

    JoshG20/DJI-MIPI-Switch

    2-Camera Input MIPI Switch for Caddx Vista/DJI FPV V1/Runcam Link systems

    11 parts11CC0-1.0

Similar boards

  • 4 layers29 × 50.3 mmLg hvac esp32, the printed circuit board in 3D

    Lg hvac esp32

    JanM321/esphome-lg-controller

    Wired controller for LG HVAC units using ESPHome and ESP32

    15 parts2920BSD
  • 4 layers33.5 × 49 mmProbecard mmcx, the printed circuit board in 3D

    Probecard mmcx

    azonenberg/starshipraider

    Open hardware test equipment

    15 parts193BSD-3-Clause
  • 4 layers28.3 × 54 mmPCB2, the printed circuit board in 3D

    PCB2

    lukasloetkolben/OpenpilotHardware

    Welcome to the Openpilot Hardware Collection!

    15 parts95MIT
  • 4 layers59 × 32 mmCp pi if fit shield, the printed circuit board in 3D

    Cp pi if fit shield

    niklasekstrom/clockport_pi_interface

    Amiga clock port to Raspberry Pi interface

    15 parts61GPL-3.0
  • 4 layers19.5 × 10.5 mmUniversalStepDown, the printed circuit board in 3D

    UniversalStepDown

    RoboticsBrno/RB0005-UniversalStepDown

    Universal step-down module

    15 parts26CC-BY-SA-4.0
  • 4 layers58.4 × 67.3 mmPico de gallo, the printed circuit board in 3D

    Pico de gallo

    OpenDevicePartnership/pico-de-gallo

    A tool for testing Embedded Rust drivers for discrete I2C/SPI components.

    15 parts21MIT
  • 4 layers114 × 52 mmLED heatplate, the printed circuit board in 3D

    LED heatplate

    lenaschimmel/bestelampe

    Die beste Lampe

    15 parts18

Questions

How big is the MIPI Switch V1.1 PCB?

It measures 30.9 × 30.9 mm and has 4 copper layers, 1.58 mm thick.

What parts does the MIPI Switch V1.1 use?

15 parts, built around the PI3WVR646GEEX. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the MIPI Switch V1.1 KiCad files?

From the JoshG20/DJI-MIPI-Switch repository on GitHub, at the commit this page was made from: the board is MIPI Switch V1.1/MIPI Switch V1.1.kicad_pcb and its schematic MIPI Switch V1.0/MIPI Switch V1.0.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the MIPI Switch V1.1 design in my own project?

Its repository publishes it under the CC0-1.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).