
Encoder
byrantech/laptop
anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

Air Gapped (except configuration) TOTP Hardware key, using the nRF52840.
NiceTOTP is an open-source printed circuit board by ICantMakeThings, from the ICantMakeThings/NiceTOTP repository on GitHub, published under the MIT licence. It is a 2-layer board of 20.5 × 46.5 mm with 7 parts on 27 nets, routed with 42 tracks and 11 vias.
Its parts include 5 connectors and 2 switches. It belongs with the nRF52 and nRF5x boards of this library.
Time-based one-time password (TOTP). aka: 2FA! A alternetive to Authy / Google Authenticator.
Full offline, Air Gapped. And Standalone once all Keys have been added.
TOTP keys and other FS are stored in an AES-256-GCM encrypted vault, with a key derived from the passcode using PBKDF2-HMAC-SHA-256. Vaults use a random starting IV followed by monotonically increasing IVs.
A four-digit passcode is still vulnerable to offline guessing if an attacker extracts the flash. Use a longer, unpredictable numeric passcode; a lengt of 13 can make a attacker wait up to 8 years on the most common GPU*
There are a few reasons why I made this device, mainly to lose dependence of my phone. But not just, What if your phone breaks, bricks, or something else? I rather have lots of devices that don't depend on eachother rather than a all in one for that reason, plus most "universal" stuff performs worse than a specific device for that single function. As of right now, I'd say it's almost complete (enough to daily drive), possibly a few more hardware security features, maybe UI polishing, fixing any bugs i haven't found yet and should be perfect. The cost is ~£6 excluding 3D printing.
Note: These are referral links. If you purchase through it, I earn a commission at no extra cost to you.

setunixtime example: setunixtime 1751925355setunixtime stores the real time for future auto-calibration which after 30 days it will compensate for any drift in the DS3231.manualcalibration <offset> example: manualcalibration 3 sets the DS3231 aging register from -128 to 127 and locks automatic calibrationlockcalibration stops auto-calibrationunlockcalibration turns back on auto-calibrationgetcalibration reports the aging offset, baseline timestamp, and lock stateclearcalibration clears the aging correction and removes the stored calibration baselineadd <username> <base32secret> example: add test JBSWY3DPEHPK3PXP (Compare)listdel <GetTheIDFromListCommand> example: del 1factoryreset (Power cycle after)If you don't care about proper security*, download the NiceTOTP-ConfiguratorNext and use the unsigned NiceTOTP-V1x.uf2 firmware.
*Or if you just want to test the device without commiting to the protected bootloader / hassle with setting it up or not owning a ST-Link
Signed.zip from latest release, and follow
Protected installation (Also includes installing from source)In 2 months the RTC drifted 8s forward. (Now there is a calibration feature, so should be better, to be commented on further.)
Battery seems to last about 1 year with a 1000mAh Battery.
Make sure not to let it discharge as it will go in a soft brick, to unbrick you just press rst
50000| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | Conn_01x13_Pin | Connector_PinHeader_2.54mm:PinHeader_1x13_P2.54mm_Vertical | J1, J2 |
| 2 | SW_Push | Button_Switch_SMD:SW_Push_1TS009xxxx-xxxx-xxxx_6x6x5mm | SW1, SW2 |
| 1 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | Conn_01x04_Socket | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | Conn_01x05_Pin | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J3 |

byrantech/laptop
anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.



AxxAxx/AxxSolder
STM32 Based soldering station for JBC cartridges, 9-24 VDC and USB-PD power


jamro/tiny-engineer
A small desktop robot that brings an AI coding assistant to life, physically acting out when it reads files, thinks, writes code, and finishes work.

hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

It measures 20.5 × 46.5 mm and has 2 copper layers, 1.6 mm thick.
7 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ICantMakeThings/NiceTOTP repository on GitHub, at the commit this page was made from: the board is PCB/NiceTOTP.kicad_pcb and its schematic PCB/NiceTOTP.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).