Skip to the content
2 layers85 × 60 mmNeurofly controller, the printed circuit board in 3D

Neurofly controller

HisarCS/neurofly

This directory contains the custom KiCad hardware project files for the NeuroFly Quadcopter Flight Controller Carrier Board, powered by the Seeed Studio XIAO ESP32-C6.

Size
85 × 60 mm
Copper layers
2
Thickness
1.6 mm
Parts
9
Nets
10
Pads
16
Tracks, vias
0, 0
Routed
Not yet
KiCad
KiCad 7 (file 20221018)
Created
22 Oct 2026
Updated
22 Oct 2026

Overview

Neurofly controller is an open-source printed circuit board by HisarCS, from the HisarCS/neurofly repository on GitHub, published under the MIT licence. It is a 2-layer board of 85 × 60 mm with 9 parts on 10 nets.

README

hardware/kicad/drone_board/README.md

NeuroFly Drone Carrier PCB (KiCad) 🛠️

This directory contains the custom KiCad hardware project files for the NeuroFly Quadcopter Flight Controller Carrier Board, powered by the Seeed Studio XIAO ESP32-C6.


📐 Board Specifications

  • Dimensions: 36.0 mm × 36.0 mm (standard micro quadcopter form factor)
  • Mounting Hole Pattern: 30.5 mm × 30.5 mm (M2 nylon hardware)
  • Center Cutout: 12.0 mm × 12.0 mm internal cutout to reduce All-Up-Weight (AUW)
  • Substrate: 1.0mm or 1.2mm FR4 (recommended for low weight) / Single-sided copper for FabLab CNC milling
  • Target Weight: ~2.8 grams (bare PCB)

⚠️ Project status: SKELETON, NOT A MANUFACTURABLE DESIGN

Honest inspection of the files in this directory (v0.2.0):

  • neurofly_drone.kicad_sch: contains the title block and a library of symbol definitions only. There are no placed component instances (no (symbol (lib_id ...)) entries), no net labels, and a single stray wire. It is not a complete schematic, ERC has not been run, and nothing is wired.
  • neurofly_drone.kicad_pcb: contains the 36 x 36 mm outline, a 12 x 12 mm centre cutout, and silkscreen text (title, M1-FL..M4-RL). It has no footprints, no tracks, no vias, no copper zones and no mounting-hole footprints (the 30.5 mm hole pattern is described in text only).
  • No DRC has been run and the boards are NOT routed. Do not send these files to a fab. Treat them as a starting point: the board outline, mounting holes and silkscreen labels are a head start, the circuit still has to be drawn and routed.
  • The XIAO symbol pin names for D8/D9/D10 were corrected in v0.2.0 to GPIO19/GPIO20/GPIO18 (see hardware/schematics/PINOUT.md; verify against the Seeed pinout before ordering).
  • Until the KiCad design is completed, build the electronics from hardware/schematics/PINOUT.md on perfboard or a milled board you design yourself, or complete the KiCad project as a student/teacher exercise.

⚡ Circuit Architecture (design intent)

  1. Microcontroller Socket:
    • 2× 7-pin 2.54mm pitch headers or direct surface-mount soldering for Seeed Studio XIAO ESP32-C6.
  2. Motor Driver Subsystem (4 Channels):
    • MOSFETs: AO3400A (30V, 5.7A N-Channel MOSFET in SOT-23)
    • Flyback Protection: SS14 (SMA footprint) Schottky barrier diodes across motor terminals (1N5819 only as a through-hole DO-41 alternative)
    • Gate Drive: 100Ω series resistor + 10kΩ pull-down per channel (4+4 resistors) to ensure zero throttle upon boot; AO3400A is fully enhanced at 3.3 V gate drive
  3. Sensor Bus (I2C):
    • 4-Pin header (3V3, GND, SDA/GPIO22, SCL/GPIO23) for MPU6050 6-DOF IMU and optional VL53L0X or VL53L1X ToF laser ranger (same I2C address 0x29; firmware 0.3.0 auto-detects).
  4. Telemetry & Safety:
    • Voltage divider (2× 10kΩ 1% resistors) mapping 1S LiPo (3.0V - 4.2V) to 1.5V - 2.1V for ADC readout. Battery sense goes to D2/GPIO2 (ADC1_CH2); the Rear-Right motor gate net is on D6/GPIO16 (motors: D0 FL, D1 FR, D6 RR, D3 RL). See hardware/schematics/PINOUT.md. Note: the symbol library in the .kicad_sch is unchanged and no nets are placed yet.
    • Status LED / buzzer on D7/GPIO17; optional ToF XSHUT on D8/GPIO19.
    • Flyback diode: use SS14 in the SMA footprint (D_SMA). The symbol in the .kicad_sch currently carries D_SOD-123, which does not match SS14 (SMA) or 1N5819 (DO-41); change the footprint to D_SMA when parts are placed. Known mismatch, not yet fixed in the .kicad files.

🏭 Digital Fabrication Guide (FabLab Roland SRM-20)

Students can mill this PCB in the FabLab using standard PCB milling machines:

  1. Isolation Milling:
    • Endmill: 1/64" flat endmill (or 0.2mm - 0.4mm V-bit 30°)
    • Cut depth: 0.04 mm - 0.08 mm
    • Spindle speed: 8,000 - 15,000 RPM
    • Feedrate: 3 - 4 mm/s
  2. Drilling & Edge Cutout:
    • Endmill: 1/32" flat endmill
    • Multi-pass cutting: 0.4mm depth per pass through 1.2mm FR1 / copper clad board.

🧑‍🎓 Student Soldering Sequence (Step-by-Step)

  1. Passives First (SMD 0805): Solder 4× 100Ω gate resistors, 4× 10kΩ gate pull-downs and 2× 10kΩ battery-divider resistors.
  2. Semiconductors: Solder the four AO3400 SOT-23 MOSFETs and SS14 Schottky diodes (note polarity line towards +3.7V).
  3. Decoupling Capacitor: Solder 10uF ceramic / low-ESR capacitor near the battery pad.
  4. Headers / Module: Solder female headers for XIAO ESP32-C6 and the I2C IMU board.
  5. Power Cable: Solder JST-PH 2.0 or BT2.0 pigtail with correct polarity (Red = +3.7V, Black = GND).
  6. Continuity & Short-Circuit Check: Verify with multimeter in continuity mode that +3.7V and GND are NOT shorted before connecting battery!

More from HisarCS/neurofly

1
  • 2 layers36 × 36 mmNeurofly drone, the printed circuit board in 3D

    Neurofly drone

    HisarCS/neurofly

    This directory contains the custom KiCad hardware project files for the NeuroFly Quadcopter Flight Controller Carrier Board, powered by the Seeed Studio XIAO ESP32-C6.

    9 partsMIT

Similar boards

  • 2 layers103 × 30.5 mmTS Back Endcap, the printed circuit board in 3D

    TS Back Endcap

    EEVengers/ThunderScope

    ThunderScope GitHub Repo

    9 parts1.3kMIT
  • 2 layers31.8 × 47.6 mmNGC 38 connector, the printed circuit board in 3D

    NGC 38 connector

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    9 parts1.2k
  • 2 layers24 × 27.3 mmExpansion Card Retrofit, the printed circuit board in 3D

    Expansion Card Retrofit

    FrameworkComputer/ExpansionCards

    Reference designs and documentation to create Expansion Cards for the Framework Laptop

    9 parts1.1kCC-BY-4.0
  • 2 layers15.6 × 17.3 mmSKR Mini TFT Thermistor Board, the printed circuit board in 3D

    SKR Mini TFT Thermistor Board

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    9 parts1.1kGPL-3.0
  • 2 layers39.1 × 49.5 mmLearnoliver, the printed circuit board in 3D

    Learnoliver

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    9 parts915
  • 2 layers17.4 × 16.9 mmToolhead, the printed circuit board in 3D

    Toolhead

    tanaes/whopping_Voron_mods

    9 parts787GPL-3.0
  • 2 layers9.8 × 108 mmExpander, the printed circuit board in 3D

    Expander

    wntrblm/Castor_and_Pollux

    A Juno-inspired dual oscillator

    9 parts587
  • 2 layersKeyboard after, the printed circuit board in 3D

    Keyboard after

    adamws/kicad-kbplacer

    KiCad plugin for automatic keyboard's key placement and routing

    9 parts547GPL-3.0

Questions

How big is the Neurofly controller PCB?

It measures 85 × 60 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Neurofly controller use?

9 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Neurofly controller KiCad files?

From the HisarCS/neurofly repository on GitHub, at the commit this page was made from: the board is hardware/kicad/controller_board/neurofly_controller.kicad_pcb and its schematic hardware/kicad/controller_board/neurofly_controller.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Neurofly controller design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).