Skip to the content
2 layers34 × 18.8 mm433 MHz RF Module, the printed circuit board in 3D

📡 Compact open-hardware 433MHz ASK RF transmitter module with LC tuning, transistor RF stage, helical antenna, PCB layout, and 3D hardware design for embedded wireless communication projects.

Size
34 × 18.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
12
Nets
9
Pads
24
Tracks, vias
48, 4
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
15 Jun 2026
Updated
15 Jun 2026

Overview

433 MHz RF Module is an open-source printed circuit board by Hirusha785, from the Hirusha785/433MHz-ASK-RF-Transmitter-Module repository on GitHub, published under the MIT licence. It is a 2-layer board of 34 × 18.8 mm with 12 parts on 9 nets, routed with 48 tracks and 4 vias.

Its parts include 2 capacitors, 2 resistors, 2 transistors, 2 inductors and 1 connector. It belongs with the radio and wireless boards of this library.

README

README.md

📡 433MHz ASK RF Transmitter Module

Status Frequency Modulation Hardware Platform License

🚀 Overview

433MHz ASK RF Transmitter Module is a compact open-hardware wireless transmitter PCB designed for sending 433MHz Amplitude Shift Keying signals from microcontrollers and embedded systems.

This project includes a custom schematic, PCB layout, RF coil antenna section, transistor-based RF stage, LC tuning network, and simple 3-pin interface for easy integration with Arduino, ESP32, STM32, Raspberry Pi Pico, and other embedded platforms.

The module is suitable for RF learning, short-range wireless communication, remote-control experiments, sensor transmitters, IoT nodes, and custom embedded hardware projects.


✨ Key Features

  • 📡 433MHz RF transmission
  • 📶 ASK modulation
  • 🔌 Simple 3-pin interface: VCC, DATA, GND
  • ⚡ Transistor-based RF driver stage
  • 🧲 LC tuning network
  • 🔁 Microcontroller-controlled data transmission
  • 📻 Helical antenna support
  • 🧩 Compact PCB layout
  • 🛠️ Open-hardware design
  • 🧪 Useful for RF testing, learning, and prototyping

🧠 Technical Description

This module is designed to transmit digital data using Amplitude Shift Keying at approximately 433MHz.

A microcontroller sends a digital signal to the DATA pin. This signal controls the transmitter stage and modulates the RF carrier amplitude. The RF signal is generated and shaped using transistor stages, coils, capacitors, and a frequency reference section.

The output is transmitted through the antenna section, which can use a helical antenna or a properly sized wire antenna depending on range and space requirements.


🧱 System Block Diagram

text
Microcontroller GPIO
        ↓
DATA Input
        ↓
ASK Modulation Stage
        ↓
RF Oscillator / Frequency Reference
        ↓
Transistor RF Driver Stage
        ↓
LC Tuning Network
        ↓
Antenna Output
        ↓
433MHz Wireless Transmission

🔌 Pinout

PinNameDescription
1VCCPower input
2DATAASK data input from microcontroller
3GNDGround connection

🧩 Main Components

ComponentValue / TypeFunction
AE1AntennaTransmits the 433MHz RF signal
L18 turnsRF tuning / oscillator coil
L23 turnsAntenna coupling / RF output coil
C17pFRF tuning capacitor
C27pFAntenna coupling capacitor
R127kΩBiasing resistor
R227kΩDATA input / modulation resistor
Q12SC4213RF transistor stage
Q22SC4213Modulation / RF driver transistor stage
Y1Crystal / ResonatorFrequency reference component
J13-pin connectorVCC, DATA, GND interface

⚙️ Hardware Design Sections

1. Power Input Section

The module receives power through the VCC and GND pins.

A stable power supply is important because RF output strength and frequency stability can be affected by voltage noise or weak supply current.


2. DATA Input Section

The DATA pin receives a digital signal from a microcontroller.

Typical connection:

text
Microcontroller VCC   →  VCC
Microcontroller GPIO  →  DATA
Microcontroller GND   →  GND

The DATA input controls the ASK modulation behavior of the transmitter.


3. RF Oscillator Section

The oscillator section generates the RF carrier signal around the 433MHz band.

The frequency reference component, transistor stage, coils, and capacitors help form the RF signal generation network.


4. ASK Modulation Section

ASK means Amplitude Shift Keying.

In this module, the input data changes the amplitude of the RF signal.
When the DATA signal changes between HIGH and LOW states, the RF output amplitude changes accordingly.


5. RF Driver Stage

The transistor-based RF stage helps drive the RF signal toward the antenna section.

This stage is important for signal strength and transmission range.


6. Antenna Output Section

The antenna section radiates the 433MHz RF signal.

A properly designed antenna improves:

  • Transmission distance
  • Signal stability
  • RF efficiency
  • Receiver detection quality

🧪 Testing Methods

You can test this transmitter module using:

  • Arduino
  • ESP32
  • STM32
  • Raspberry Pi Pico
  • Oscilloscope
  • SDR receiver
  • 433MHz ASK receiver module
  • Logic analyzer
  • RF spectrum analyzer

Example testing flow:

text
Microcontroller
      ↓
433MHz ASK Transmitter Module
      ↓
Wireless RF Signal
      ↓
433MHz ASK Receiver Module
      ↓
Microcontroller / Logic Analyzer

🧑‍💻 Arduino Basic ASK Transmit Code

cpp
#define TX_DATA_PIN 2

const unsigned int BIT_DELAY_US = 500;

void sendBit(bool bitValue) {
  digitalWrite(TX_DATA_PIN, bitValue ? HIGH : LOW);
  delayMicroseconds(BIT_DELAY_US);
}

void sendByte(byte data) {
  for (int i = 7; i >= 0; i--) {
    sendBit((data >> i) & 0x01);
  }
}

void sendFrame(byte payload) {
  // Preamble for receiver synchronization
  for (int i = 0; i < 8; i++) {
    sendByte(0xAA);
  }

  // Sync bytes
  sendByte(0x2D);
  sendByte(0xD4);

🧑‍💻 ESP32 Basic ASK Transmit Code

cpp
#define TX_DATA_PIN 27

const unsigned int BIT_DELAY_US = 500;

void sendBit(bool bitValue) {
  digitalWrite(TX_DATA_PIN, bitValue ? HIGH : LOW);
  delayMicroseconds(BIT_DELAY_US);
}

void sendByte(uint8_t data) {
  for (int i = 7; i >= 0; i--) {
    sendBit((data >> i) & 0x01);
  }
}

void sendFrame(uint8_t payload) {
  // Preamble for receiver synchronization
  for (int i = 0; i < 8; i++) {
    sendByte(0xAA);
  }

  // Sync bytes
  sendByte(0x2D);
  sendByte(0xD4);

🔬 Oscilloscope / RF Testing

Recommended testing points:

Test PointPurpose
DATA pinCheck microcontroller input waveform
Q2 stageCheck modulation switching behavior
Oscillator sectionVerify RF activity
Antenna outputCheck transmitted RF signal
Receiver outputConfirm wireless transmission

🖼️ Project Preview

Schematic

image

Schematic

PCB Layout

image

PCB Layout

3D View

image image image image

3D View


🛠️ PCB Design Notes

  • Keep the antenna trace short and clean.
  • Keep RF traces away from noisy digital signals.
  • Use a stable ground reference around the RF section.
  • Place RF tuning components close to the transistor RF stage.
  • Avoid unnecessary long traces in the oscillator section.
  • Keep the DATA input trace away from the antenna path where possible.
  • Use short routing between the LC network and antenna output.
  • Avoid sharp corners in RF traces.
  • Test the transmitter with a receiver or SDR before final production.
  • RF performance depends heavily on antenna design, PCB layout, supply voltage, and component tolerance.

📡 Antenna Notes

For 433MHz, a common quarter-wave wire antenna length is approximately:

text
17.3 cm

A helical antenna can also be used for compact designs.

The final range depends on:

  • Antenna type
  • Antenna tuning
  • Supply voltage
  • PCB layout
  • Receiver sensitivity
  • Environmental interference
  • Distance and obstacles

⚠️ Important Notes

This project is intended for:

  • Educational use
  • RF learning
  • Embedded hardware experiments
  • Short-range wireless prototyping
  • ASK transmitter testing

RF transmission is regulated in many countries.
Before commercial or public deployment, make sure the design follows local RF regulations, frequency limits, duty-cycle limits, and output power limits.


👨‍💻 Author

Designed by Fernando S.M.H.G

Open-hardware RF transmitter project for embedded systems, electronics learning, RF experimentation, and wireless communication projects.


📜 License

This project is released under the MIT License.

You are free to use, modify, improve, and share this project with proper attribution.


⭐ Support

If this project helps you, consider giving the repository a star.

text
Made for RF learning, embedded systems, and open-hardware development.
text

Parts

12
QtyValueFootprintReferences
227kResistor_SMD:R_0805_2012MetricR1, R2
22SC4213Package_TO_SOT_SMD:SOT-323_SC-70Q1, Q2
27 pFCapacitor_SMD:C_1206_3216MetricC1, C2
13TurnsInductor_THT:L_Axial_L5.3mm_D2.2mm_P7.62mm_Horizontal_Vishay_IM-1L2
18TurnsInductor_THT:L_Axial_L7.0mm_D3.3mm_P12.70mm_Horizontal_Fastron_MICCL1
1AntennaRF_Antenna:NiceRF_SW868-TH13_868MhzAntenna
1Conn_01x03_PinConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_HorizontalJ1
1CrystalCrystal:Crystal_HC52-6mm_HorizontalY1

The 11 most common of 12 parts.

Similar boards

  • 2 layersNrf bga, the printed circuit board in 3D

    Nrf bga

    github-linguist/linguist

    Language Savant. If your repository's language is being reported incorrectly, send us a pull request!

    12 parts14kMIT
  • 2 layers66.9 × 74.5 mmDeskHop, the printed circuit board in 3D

    DeskHop

    hrvach/deskhop

    Fast Desktop Switching Device

    12 parts7.9kGPL-3.0
  • 2 layers40 × 15 mmSensors, the printed circuit board in 3D

    Sensors

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    12 parts3kApache-2.0
  • 2 layers42.7 × 56.5 mmTle6240 driver, the printed circuit board in 3D

    Tle6240 driver

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    12 parts1.2k
  • 2 layers49 × 25 mm5v boost regulator, the printed circuit board in 3D

    5v boost regulator

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    12 parts915
  • 2 layers28.3 × 10.3 mmTap Photosensor PCB, the printed circuit board in 3D

    Tap Photosensor PCB

    VoronDesign/Voron-Tap

    Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Tap offers many advantages:

    12 parts716GPL-3.0
  • 2 layers25.4 × 70.4 mmTpmsniffer, the printed circuit board in 3D

    Tpmsniffer

    stacksmashing/pico-tpmsniffer

    A simple, very experimental TPM sniffer for LPC bus

    12 parts696

Questions

How big is the 433 MHz RF Module PCB?

It measures 34 × 18.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the 433 MHz RF Module use?

12 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the 433 MHz RF Module KiCad files?

From the Hirusha785/433MHz-ASK-RF-Transmitter-Module repository on GitHub, at the commit this page was made from: the board is 433 MHz RF Module.kicad_pcb and its schematic 433 MHz RF Module.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the 433 MHz RF Module design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).