Skip to the content
2 layers99.3 × 83.8 mmATMEGA328PB Proto Board, the printed circuit board in 3D

ATMEGA328PB Proto Board

HSBallina/ATMEGA328PB_proto

ATMEGA328PB microcontroller breakout

Size
99.3 × 83.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
41
Nets
47
Pads
157
Tracks, vias
242, 46
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
30 Mar 2021
Updated
31 Jul 2019

Overview

ATMEGA328PB Proto Board is an open-source printed circuit board by HSBallina, from the HSBallina/ATMEGA328PB_proto repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 99.3 × 83.8 mm with 41 parts on 47 nets, routed with 242 tracks and 46 vias.

It is built around the ATMEGA328PB-AU. Its parts include 18 connectors, 9 capacitors, 4 resistors, 2 switches and 1 IC. It belongs with the interfaces and adapters boards and the AVR (ATmega, ATtiny) boards of this library.

Main components

1

README

README.md

ATMEGA328PB breakout & prototyping board

This is a breakout/prototyping board for the ATMEGA328PB microcontroller which comes in the TQFP-32 format. It allows programming of the chip and breaks out all the pins to standard DuPont headers for project prototyping. My plan is to mount this PCB on a baseboard alongside a breadboard.

The microcontroller chip is placed in a TQFP-32 adapter, such as this one. These come with carrier boards to make the adapter fit standard DIP footprints. But my board doesn't use this - it just uses the main adapter itself which I have soldered into my PCB.

The pins for the four ports, B, C, D and E are gathered together logically (whereas they are somewhat scattered around on the microcontroller chip pinout itself).

Features

  • The AVCC pin is connected to VCC using a low-pass filter - ie, via a 10µH inductor with a 0.1µF capacitor to GND. This is Atmel's recommended setup which you want to use the analogue features of the microcontroller but don't want to go to the trouble of providing a separate analogue supply.
  • There's a standard 6-pin header to connect an ISP programmer auch as the ATMEL-ICE.
  • The ~RESET pin (PC6) has a pullup resistor and a tactile button to reset the microcontroller.
  • The standard I2C pins (PC4, PC5) both have two additional pins for easy use of more than one I2C device. The additional pins are accompanied by +5V and GND pins. Onboard 10kΩ pullup resistors can be selected or deselected using jumpers.
  • Female headers allow the use of an external crystal. This can be selected or deselected using jumpers. Onboard 22pF capacitors are connected between each leg of the crystal and GND.
  • The standard UART pins – RX (PD0) and TX (PD1) have additional pins. These are in a row of six pins, including a GND connection, designed to match the normal order of connections on an FTDI USB-serial cable. Two of the other pins - RTS and CTS - are connected to two more pins. You can then use short female-female jumper cables to connect RTS and DTS to the GPIO pins of your choice.
  • Finally, there are three lots of 4-pin connectors all tied to GND. Marked as 'test points', these are for the easy attachment of the GND clip for oscilloscope probes.
  • There's an on-off slide switch for power. It is possible, however, that the board will be back-powered through any signals applied to the GPIO pins. Other than buffering every pin, I don't see any way to avoid this, so it's just something to watch out for.

Notes

  • The power connector is a simple two-pin header. NO REVERSE POLARITY PROTECTION IS PROVIDED. Nor is there any over-voltage protection.
  • The board is intended to be powered by 5V, although it might work on 3.3V (I haven't thought that through).

Progress

I've received the first batch of Rev 1.0 boards and have made up one, hand-soldered board. And, so far, it has worked flawlessly.


Resources

Parts

41
QtyValueFootprintReferences
30.1µFCapacitors_SMD:C_1206C1, C4, C7
310KResistors_SMD:R_1206R1, R2, R3
3GND test ptsPin_Headers:Pin_Header_Straight_1x04J15, J16, J19
21µFCapacitors_SMD:C_1206C8, C9
222pFCapacitors_SMD:C_1206C5, C6
2I2CPin_Headers:Pin_Header_Straight_1x04J6, J7
10.1µFCapacitors_ThroughHole:C_Radial_D5_L6_P2.5C3
110µHSpeculatrix_general:Inductor_Bourns-SRN5020L1
11µFCapacitors_ThroughHole:C_Radial_D5_L6_P2.5C2
1330Resistors_SMD:R_1206R4
1ATMEGA328PBSpeculatrix_microcontrollers:DIP-32_TQFP_ZIFU1
1AVR-ISPSpeculatrix_connectors:AVR_ISP_HE10_2x3CONN1
1I2C_PUPin_Headers:Pin_Header_Straight_1x03J9
1PORT BPin_Headers:Pin_Header_Straight_1x08J2
1PORT CPin_Headers:Pin_Header_Straight_1x07J3
1PORT DPin_Headers:Pin_Header_Straight_1x08J4
1PORT EPin_Headers:Pin_Header_Straight_1x05J5
1PWRLEDs:LED_1206D1
1PWR_INPin_Headers:Pin_Header_Straight_1x02J1
1PWR_OUTPin_Headers:Pin_Header_Straight_1x02J11
1RTS-CTSPin_Headers:Pin_Header_Straight_1x02J18
1SCL_PUPin_Headers:Pin_Header_Straight_1x03J10
1SW_DPDTSpeculatrix_general:SW_SMD_DPDTSW1
1Serial_PortPin_Headers:Pin_Header_Straight_1x06J17
1XTALPin_Headers:Pin_Header_Straight_1x03J13
1XTAL2_JMPPin_Headers:Pin_Header_Straight_1x03J14
1XTAL_JMPPin_Headers:Pin_Header_Straight_1x03J12
1~RESETButtons_Switches_ThroughHole:SW_PUSH_6mmSW2

The 37 most common of 41 parts.

Similar boards

  • 2 layers78 × 130 mmLofence, the printed circuit board in 3D

    Lofence

    kiu/lofence

    LoFence is a LoRaWAN capable IoT electric fence monitoring system running on the The Things Network.

    65 parts142MIT
  • 2 layers102 × 81.5 mmC64pico, the printed circuit board in 3D

    C64pico

    silvervest/c64pico

    This is a tiny emulated C64 running on a Raspberry Pi Pico! Full details of the build can be found at https://www.youtube.com/watch?v=hgLhGpbC6E4

    97 parts86
  • 2 layers58.4 × 34.3 mmSIO2SD, the printed circuit board in 3D

    SIO2SD

    c0pperdragon/SIO2SD

    An Arduino-based floppy drive emulator for the atari 8 bit computers.

    26 parts83
  • 2 layers200 × 100 mmRegalodilara, the printed circuit board in 3D

    Regalodilara

    valerionew/very-good-uc-doggos

    A special graduation present for a special friend. Six microcontrollers in one devboard

    91 parts50
  • 2 layers88.9 × 50.8 mmBLDC BIZ CARD, the printed circuit board in 3D

    BLDC BIZ CARD

    ageppert/Brushless-Motor-Biz-Card

    A brushless motor and driver built in to a business card form-factor for learning and experimenting!

    82 parts38MIT
  • 2 layers52.1 × 37.4 mmConsolizer, the printed circuit board in 3D

    Consolizer

    orangeglo/PS2PSP

    Board to connect a PS2 controller to a PSP 2000 (PSP Consolizer)

    25 parts38GPL-3.0
  • 2 layers67.3 × 54 mmJeep radio, the printed circuit board in 3D

    Jeep radio

    latonita/jeep-canbus

    Projects around CAN BUS in Chrysler Jeep - VES enabler, other small features

    52 parts30MIT
  • 2 layers91.4 × 92.5 mmNano328PB, the printed circuit board in 3D

    Nano328PB

    tomaskovacik/hw

    HW (pcb, schematics etc) for my projects

    450 parts27

Questions

How big is the ATMEGA328PB Proto Board PCB?

It measures 99.3 × 83.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the ATMEGA328PB Proto Board use?

41 parts, built around the ATMEGA328PB-AU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ATMEGA328PB Proto Board KiCad files?

From the HSBallina/ATMEGA328PB_proto repository on GitHub, at the commit this page was made from: the board is ATMEGA328PB Proto Board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the ATMEGA328PB Proto Board design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).