
5V 10A Buck
AMAR124595/5V_10A-Buck-converter
A 4 layer PCB of the 5V_10A buck convertor using TPS51397ARJER IC

1) Add explicit header pins next to the PICO. This can be useful to easily attach external equipment like a Logic Analyzer or TTL-module, or simply wires to a breadboard if needed.
Universal connector board is an open-source printed circuit board by HCL-Hbot, from the HCL-Hbot/universal_connector_board repository on GitHub. It is a 2-layer board of 113.1 × 85 mm with 103 parts on 130 nets, routed with 1,574 tracks and 239 vias.
It is built around the TSR 1-2433, TPS51397ARJER and 691401700003B, with the BSS84 and SRP6540-1R0M among its other parts. Its parts include 31 resistors, 22 capacitors, 14 connectors, 7 ICs and 3 transistors. It belongs with the RP2040 boards of this library.
This document outlines the contribution to a PCB design for project Healthbot, which is part of the Health Concept Lab of HAN University of Applied Sciences. It is part of a semester 6 student project including 3 Embedded Systems Engineers and 4 Industrial Design Engineers. The goal for this project was developing a social robot for healthcare, with several functionalities. This PCB is made to be integrated in the robot, but also made quite universal, so it can be used in new robot designs. In the folder media, there are images of the PCB. Because this was a first version, please look at the recommendations below!
Some components on the PCB that were needed are the I/O Expander, voltage regulators and an UART multiplexer.
Because the GPIO pins of the Pico were completely full and we still needed some, we added an I/O Expander which works with I2C. This expander has 8 I/O channels, which are also all connected.
Because of the several needed voltages for the components, two regulators are on the PCB. There is 12 Volt coming in to the PCB via the block terminal. This is guided to a TSR 1-2433, which converts it to 3.3V. Also a 5V regulator is on the PCB, which was more complicated because it has to have a high output current due to the ledstrips needing lots of current.
The motor driver modules can be controlled via UART communication. Because the Pico doesn't have lots of UART channels, and are already needed for communication between the RPI4 and the Pico e.g., an UART Multiplexer was added. Although we don't use it to control our motor drivers, this is still a possibility because of this multiplexer. This also provided the board with 2 extra UART possibilities for whatever component needs it.
Below are recommendations for the next group that gets to design a PCB for project Healthbot. These are additions to the previous named issues that need to be adjusted. These recommendations are up to the next developer to decide.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 100k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3, R4, R5, R6, R7, R8, R12 |
| 4 | 0.10μF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C19, C20, C21 |
| 4 | 47µF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C11, C12, C13, C14 |
| 4 | 50k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R23, R25, R26, R28 |
| 4 | Jumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP2, JP3, JP4, JP5 |
| 3 | 0.1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C7, C8, C10 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R19, R20, R21 |
| 2 | 0 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R11, R18 |
| 2 | 100 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R27, R30 |
| 2 | 1000μF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C3 |
| 2 | 100nF 50V | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C16, C18 |
| 2 | 15k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R14, R17 |
| 2 | 22uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C5, C6 |
| 2 | 2N7002 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | 47 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R22, R29 |
| 2 | 470 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R9, R10 |
| 2 | Elec_Capacitor | SamacSys_Parts:CAPAE1000X1050N | C15, C17 |
| 2 | TMC2209_MotorDriver | Healthbot-Footprints:MODULE_TMC2209_SILENTSTEPSTICK | U1, U2 |
| 2 | TP_GND | TestPoint:TestPoint_Pad_D1.5mm | TP1, TP14 |
| 1 | clipboard:d0ed0aed-a5b7-4fbb-959d-d2596cb26e0d | Logo | |
| 1 | 100nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C22 |
| 1 | 100pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C9 |
| 1 | 110k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R16 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4 |
| 1 | 330k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R13 |
| 1 | 4.7k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R31 |
| 1 | 51.1 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R15 |
| 1 | 691401700003B | SamacSys_Parts:691401700003B | J1 |
| 1 | 75 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R24 |
| 1 | BSS84 | Package_TO_SOT_SMD:SOT-23 | Q3 |
| 1 | Cheeks | Connector_JST:JST_XH_S2B-XH-A_1x02_P2.50mm_Horizontal | J10 |
| 1 | Display1 | Connector_JST:JST_XH_S7B-XH-A_1x07_P2.50mm_Horizontal | J2 |
| 1 | Display2 | Connector_JST:JST_XH_S7B-XH-A_1x07_P2.50mm_Horizontal | J3 |
| 1 | Extra MUX_UART | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J6 |
| 1 | Extra VCC/GND | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J15 |
| 1 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | Ledstrip1 | Connector_JST:JST_XH_S4B-XH-A_1x04_P2.50mm_Horizontal | J8 |
| 1 | Ledstrip1_VCC | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP6 |
| 1 | Ledstrip2 | Connector_JST:JST_XH_S3B-XH-A_1x03_P2.50mm_Horizontal | J5 |
| 1 | Ledstrip2_VCC | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP7 |
| 1 | MD_SW1 | Connector_JST:JST_XH_S2B-XH-A_1x02_P2.50mm_Horizontal | J11 |
| 1 | MD_SW2 | Connector_JST:JST_XH_S2B-XH-A_1x02_P2.50mm_Horizontal | J12 |
| 1 | Motor1 | Connector_JST:JST_XH_S4B-XH-A_1x04_P2.50mm_Horizontal | J13 |
| 1 | Motor2 | Connector_JST:JST_XH_S4B-XH-A_1x04_P2.50mm_Horizontal | J14 |
| 1 | Mouth | Connector_JST:JST_XH_S2B-XH-A_1x02_P2.50mm_Horizontal | J9 |
| 1 | Mux_Vcc | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP1 |
| 1 | RASPBERRY_PI_4B_4GB | Healthbot-Footprints:MODULE_RASPBERRY_PI_4B_4GB | U3 |
| 1 | RPI_Pico_EvaluationBoard | Healthbot-Footprints:RPi_Pico_SMD_TH | IC1 |
| 1 | Radar | Connector_JST:JST_XH_S8B-XH-A_1x08_P2.50mm_Horizontal | J7 |
| 1 | SN74LV4052ADR | Healthbot-Footprints:SOIC127P600X175-16N | IC2 |
| 1 | SRP6540-1R0M | Healthbot-Footprints:INDPM7265X400N | L1 |
| 1 | SW_Push | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | SW1 |
| 1 | TCA9534DWR | SamacSys_Parts:SOIC127P1030X265-16N | IC4 |
| 1 | TPS51397ARJER | Healthbot-Footprints:QFN45P300X300X100-21N-D | IC3 |
| 1 | TP_12V | TestPoint:TestPoint_Pad_D1.5mm | TP3 |
| 1 | TP_3.3V | TestPoint:TestPoint_Pad_D1.5mm | TP2 |
| 1 | TP_5V | TestPoint:TestPoint_Pad_D1.5mm | TP4 |
| 1 | TP_5V_RPI4 | TestPoint:TestPoint_Pad_D1.5mm | TP5 |
| 1 | TP_RX | TestPoint:TestPoint_Pad_D1.5mm | TP6 |
| 1 | TP_TX | TestPoint:TestPoint_Pad_D1.5mm | TP7 |
| 1 | TP_VCC_LEDC | TestPoint:TestPoint_Pad_D1.5mm | TP13 |
| 1 | TP_VCC_LEDM | TestPoint:TestPoint_Pad_D1.5mm | TP12 |
| 1 | TP_VCC_MUX | TestPoint:TestPoint_Pad_D1.5mm | TP10 |
| 1 | TP_VCC_STRIP1 | TestPoint:TestPoint_Pad_D1.5mm | TP8 |
| 1 | TP_VCC_STRIP2 | TestPoint:TestPoint_Pad_D1.5mm | TP9 |
| 1 | TP_VSYS | TestPoint:TestPoint_Pad_D1.5mm | TP11 |
| 1 | TSR_1-2433 | Healthbot-Footprints:TSR-1-2433 | PS1 |

AMAR124595/5V_10A-Buck-converter
A 4 layer PCB of the 5V_10A buck convertor using TPS51397ARJER IC



Staacks/there.oughta.be
Projects featured on my blog at https://there.oughta.be

j-marjanovic/ocs-tray-mezzanine-adapter
PCIe adapter for an FPGA accelerator for Open CloudServer


TangoPush/MP1Flight
STM32MP1 based flight controller based off the Pixracer.

AlexW-proj/ion-pump-controller
open source controller that takes 24V in and spits out 0 - 7000V, set by a knob with an adjustable ramp time
It measures 113.1 × 85 mm and has 2 copper layers, 1.6 mm thick.
103 parts, built around the TSR 1-2433, TPS51397ARJER, 691401700003B and BSS84. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the HCL-Hbot/universal_connector_board repository on GitHub, at the commit this page was made from: the board is KiCAD_Proj/universalConnectorBoard.kicad_pcb and its schematic KiCAD_Proj/PowerManagement.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask HCL-Hbot before reusing the design.