
Type f
google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards

Simple PCB to control computer fan speed with a atinny88
Step fan speed is an open-source printed circuit board by GuillemCabo, from the GuillemCabo/step_fan_speed repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 47.5 × 20.5 mm with 25 parts on 35 nets, routed with 259 tracks and 55 vias.
It is built around the ATTINY88-MU. Its parts include 6 resistors, 5 capacitors, 4 connectors, 2 ICs and 2 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Simple PCB to control computer fan speed with a atinny88
The board runs out of the fan 12V, step down to 3.3V with an LDO.
It provides a PWM header in and PWM out. The MCU is able to intercept the signal of the tachometer and generated a new PWM signal.
The uart is accesible through a two pin headeris. External FTDI bridge is required if you want to connect it to the computer.
The board is programmed thorugh ISP with a Tag-connect cable or UART if a bootloader if it has been previously programmed.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 100 | Resistor_SMD:R_0603_1608Metric | R5, R6 |
| 2 | 10uF | Capacitor_SMD:C_0805_2012Metric | C2, C5 |
| 2 | 2K2 | Resistor_SMD:R_0603_1608Metric | R2, R3 |
| 2 | TestPoint | TestPoint:TestPoint_Pad_1.5x1.5mm | TP1, TP2 |
| 1 | 0.01uF | Capacitor_SMD:C_0603_1608Metric | C4 |
| 1 | 0.1uf | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric | C3 |
| 1 | ATtiny88-MU | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mm | U1 |
| 1 | AVR-ISP-6 | Connector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_Vertical | CON1 |
| 1 | Conn_01x02_Male | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | J3 |
| 1 | Conn_01x04_Female | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Horizontal | J1 |
| 1 | Conn_01x04_Male | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Horizontal | J2 |
| 1 | GREEN_LED | fp:KPA-1606 | D2 |
| 1 | MCSJK-6NC1-12.00-25-B | Oscillator:Oscillator_SMD_EuroQuartz_XO91-4Pin_7.0x5.0mm_HandSoldering | X1 |
| 1 | NDS03V | Button_Switch_THT:SW_DIP_SPSTx03_Slide_9.78x9.8mm_W7.62mm_P2.54mm | SW1 |
| 1 | R | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | RED_LED | fp:KPA-1606 | D1 |
| 1 | SW_Push | Button_Switch_SMD:SW_Push_1P1T_NO_CK_KSC7xxJ | SW2 |
| 1 | TAR5S15-TAR5S50 | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U2 |
| 1 | Thermistor_NTC | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_Vertical | TH1 |

google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards

davidphilipbarr/Sweep
Sweep - a small promicro based keyboard inspired by the Ferris.


hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

xyphro/UsbGpib
Versatile, cheap and portable USB to GPIB converter (USBTMC class based)


jes/scamp-cpu
A homebrew 16-bit CPU with a homebrew Unix-like-ish operating system.

It measures 47.5 × 20.5 mm and has 2 copper layers, 1.6 mm thick.
25 parts, built around the ATTINY88-MU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the GuillemCabo/step_fan_speed repository on GitHub, at the commit this page was made from: the board is BOARD/step_fan_speed.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).