Skip to the content
2 layers40.4 × 54.4 mmFuel economy meter, the printed circuit board in 3D

Fuel economy meter

Goosetaf/esp32-trip-meter1

A system for tracking trip data on an ESP32

Size
40.4 × 54.4 mm
Copper layers
2
Thickness
1.6 mm
Parts
9
Nets
32
Pads
50
Tracks, vias
29, 3
Pours
1
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
3 Jul 2023
Updated
30 Jun 2024

Overview

Fuel economy meter is an open-source printed circuit board by Goosetaf, from the Goosetaf/esp32-trip-meter repository on GitHub. It is a 2-layer board of 40.4 × 54.4 mm with 9 parts on 32 nets, routed with 29 tracks and 3 vias.

Its parts include 3 resistors, 2 diodes, 2 connectors, 1 capacitor and 1 IC. It belongs with the ESP32 boards of this library.

README

README.md

ESP32 Trip Meter

An ESP32-based trip meter primarily made for measuring fuel efficiency.

Background and motivation

I started this project in search of a solution for measuring the fuel efficiency on my '97 Volvo 940. The only real solution I found prior was the MPGuino, but I quickly realised it wasn't for my needs. What I wanted was to have a solution that was as clean as possible, so having a separate display that I had to mount somewhere was out of the question.

Instead, I built it around a standard Bluetooth OBD-II interface, which would allow any device to get information and display it in any way they want. This was perfect for my use case, as I wanted to display all the information on my phone or Android stereo via the Torque app.

Features

  • Measure fuel efficiency (L/100km)
  • Measure velocity (Km/h)
  • Measure fuel injection speed (L/h)
  • Display data through an emulated ELM327 (OBD-II) interface

Connections

  • The negative side of the injector is connected to corresponding input on the board
    • NOTE: Must be a saturation-type injector (read below)
  • A pulsed signal of the vehicle speed sensor (VSS) is connected to VSS+
    • Variable reluctance (VR) speed sensors do not seem to work

Power and ground

The ground reference and power is currently given by the USB port on the ESP32. This may change later due to being a limiting factor.

Injector types

This project is mainly made to support saturation-type injectors. If your engine uses other types of injectors, such as peak-and-hold injectors, this project will not work.

The easiest way to check this is to measure the resistance of an injector; If it has a resistance of around 12Ω, it is a saturation-type injector. If it has a resistance of around 2-3Ω, it is likely a peak-and-hold injector.

Also note that injectors that are connected for batch injection may be connected in parallel, and may in some cases display a resistance that is lower than normal.

The reason why peak-and-hold injectors will not work, is that they work differently from saturation injectors. While saturation injectors simply open while the signal is active, a peak-and-hold injector, like its name suggests, sends a high voltage signal which forces the injector open (peak). After that, a lower-voltage signal (normally around 12 volts) is pulsed through the remainder of the opening time (hold).

Platform compatibility

Since the project currently uses ESP32-specific platform code a lot, it would be difficult to port to using normal Arduino implementations. It may be possible to port it to ESP8266 devices, but they would need a discrete Bluetooth module.

Parts

9
QtyValueFootprintReferences
350KResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR1, R2, R3
23VDiode_SMD:D_SOD-123D1, D2
2Conn_01x02_FemaleConnector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_VerticalJ1, J2
10.01uFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC1
1ESP32-DEVKIT-V1ESP32_Devkit:MODULE_ESP32_DEVKIT_V1U1

Similar boards

  • 2 layers103 × 30.5 mmTS Back Endcap, the printed circuit board in 3D

    TS Back Endcap

    EEVengers/ThunderScope

    ThunderScope GitHub Repo

    9 parts1.3kMIT
  • 2 layers31.8 × 47.6 mmNGC 38 connector, the printed circuit board in 3D

    NGC 38 connector

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    9 parts1.2k
  • 2 layers24 × 27.3 mmExpansion Card Retrofit, the printed circuit board in 3D

    Expansion Card Retrofit

    FrameworkComputer/ExpansionCards

    Reference designs and documentation to create Expansion Cards for the Framework Laptop

    9 parts1.1kCC-BY-4.0
  • 2 layers15.6 × 17.3 mmSKR Mini TFT Thermistor Board, the printed circuit board in 3D

    SKR Mini TFT Thermistor Board

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    9 parts1.1kGPL-3.0
  • 2 layers39.1 × 49.5 mmLearnoliver, the printed circuit board in 3D

    Learnoliver

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    9 parts915
  • 2 layers17.4 × 16.9 mmToolhead, the printed circuit board in 3D

    Toolhead

    tanaes/whopping_Voron_mods

    9 parts787GPL-3.0
  • 2 layers9.8 × 108 mmExpander, the printed circuit board in 3D

    Expander

    wntrblm/Castor_and_Pollux

    A Juno-inspired dual oscillator

    9 parts587
  • 2 layersKeyboard after, the printed circuit board in 3D

    Keyboard after

    adamws/kicad-kbplacer

    KiCad plugin for automatic keyboard's key placement and routing

    9 parts547GPL-3.0

Questions

How big is the Fuel economy meter PCB?

It measures 40.4 × 54.4 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Fuel economy meter use?

9 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Fuel economy meter KiCad files?

From the Goosetaf/esp32-trip-meter repository on GitHub, at the commit this page was made from: the board is pcb/fuel_economy_meter.kicad_pcb and its schematic pcb/fuel_economy_meter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Fuel economy meter design in my own project?

Its repository states no licence, so its author keeps all rights: ask Goosetaf before reusing the design.