Skip to the content
2 layers55.9 × 106.7 mmUSB IO Module, the printed circuit board in 3D

A digital audio transmission specification for eurorack like modular synthesizers

Size
55.9 × 106.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
101
Nets
110
Pads
303
Tracks, vias
671, 57
Pours
1
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
28 Apr 2024
Updated
26 Oct 2024

Overview

USB IO Module is an open-source printed circuit board by Fora888, from the Fora888/fully-digital-modular-hardware-synthesizer repository on GitHub, published under the MIT licence. It is a 2-layer board of 55.9 × 106.7 mm with 101 parts on 110 nets, routed with 671 tracks and 57 vias.

It is built around the SC16IS762IPW. Its parts include 41 diodes, 5 resistors, 3 ICs, 3 connectors and 1 crystal. It belongs with the audio and music boards and the NXP (LPC, Kinetis, i.MX RT) boards of this library.

Main components

1

README

README.md

Fully digital modular synthesizer

A fully digital modular synthesizer specification

Specification

Audio data format

The audio data is transmitted and processed at 44.1kHz sample rate and 16 Bits of resolution

Data transmission

Data transmission utilizes UART in combination with a simple protocol. UART is configured at a baud rate of 2,000,000 with 8 data bits, 1 stop bit, no flow control and regular polarity. Signal levels are defined as 0V for low and 3.3V for high. However, all inputs and outputs should withstand voltages from +12V to -12V to prevent accidental damage when interfaced with analog equipment. Due to UART's limitation of transmitting only 8 bits at a time and each audio sample requiring 16 bits, each sample is transmitted as three sequential packets. Each packet consists of 6 data bits followed by 2 order bits. Therefore a full UART frame looks like the following:

1621
Start bitData bitsOrder bitsStop bit

The least significant 8 bits of a sample are sent first with order bits '00', followed by the middle 8 bits with order bits '10', and finally the most significant 4 bits with order bits '01'. The last two data bits of the last packet with order bits '01', as well as the order bit combination '11', remain unused for now but could be utilized for future extensions.

Power

Modules are connected to +5V and ground via a 6 pin, 2 row, 2.54mm (0.1 inch) spacing header connector. These use the following pinout:

5v5vGND
GNDGNDGND

This asymmetric pattern ensures, that in case the header is plugged in incorrectly, the power supply is short-circuited and the module doesn't get damaged. Therefore it is advisable for power supplys to feature some sort of fusing mechanism. Since noisy power doesn't impact the sound quality of digital audio, switching power supplys are sufficient for voltage conversion

Mechanical

Since UART necessitates only one cable for transmission, akin to mono audio, the mechanical specifications of virtually any existing analog modular synthesizer can be used. The examples are based on eurorack the eurorack specification with 128mm height and 3.5mm TS (mono) phone connectors.

Comparison to analog

Advantages

Less noise - Digital transmission ensures that the audio signal is received exactly as it was sent, without introducing noise during transmission. Furthermore many analog modules use analog-to-digital and digital-to-analog conversion, which introduce noise into the signal

Reduced complexity - Digital signals don't require clean power or buffering in order to deliver good audio. Merely two diodes and one or two resistors, which are always in the exact same configuration, are required per input or output. In addition all I/O is full 16 bit and the audio is inherently DC coupled.

Lower Price - Microprocessors are cheap and require relatively few and simple auxiliary components when compared to analog electronics. The reduced complexity of digital signal processing also leads to lower development costs.

Disadvantages

Latency - Digital signal processing always comes with latency. In case of the examples, where audio is processed in blocks of 128 samples, this latency comes in at ~3 ms per module. Fast processors can however reduce the block size, reducing the latency to half of that or even less.

Module selection - The digital protocol described is still in its early stages of development and therefore there are no manufacturers for it yet. So the only way to use it is to build your own modules

Implementations and examples

An implementation for the teensy audio library as well as several example modules can be found in the Teensy folder.

Parts

101
QtyValueFootprintReferences
36240mVMisc:D_SOD-123 HandsolderD6, D7, ID1, ID2, ID3, ID4, ID5, ID6, ID7, ID10, ID11, ID12, ID13, ID14, ID15, ID16 +20
17InputPerfboard:3.5mm Jack PerfboardIJ1, IJ2, IJ3, IJ4, IJ5, IJ6, IJ7, IJ8, OJ1, OJ2, OJ3, OJ4, OJ5, OJ6, OJ7, OJ8 +1
9100Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderOR1, OR3, OR5, OR7, OR9, OR11, OR13, OR15, OR17
91kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderIR1, IR2, IR3, IR4, IR5, IR6, IR7, IR8, R1
9900Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderOR2, OR4, OR6, OR8, OR10, OR12, OR14, OR16, OR18
5680RResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR2, R3, R4, R5, R6
5LEDLED_THT:LED_D3.0mmD1, D2, D3, D4, D5
1Channel_1_Mod_Input_GainPotentiometer:Bourns_PTV09A-4020UB103RV1
1Channel_1_Mod_Output_GainPotentiometer:Bourns_PTV09A-4020UB103RV3
1Channel_2_Mod_Input_GainPotentiometer:Bourns_PTV09A-4020UB103RV2
1Channel_2_Mod_Output_GainPotentiometer:Bourns_PTV09A-4020UB103RV4
1Power_Connector_2x3Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical_SMDJ3
1SC16IS762IPWPackage_SO:TSSOP-28_4.4x9.7mm_P0.65mmU1
1Teensy4.0Teensy:Teensy 4.0 back pinsU2
1Teensy4.0Teensy:Teensy 4.0 horizontalU2
1USB_ATeensy:USB_A_UprightJ2
1USB_BConnector_USB:USB_B_TE_5787834_VerticalJ1
1XO53Oscillator:Oscillator_SMD_EuroQuartz_XO53-4Pin_5.0x3.2mmX1

More from Fora888/fully-digital-modular-hardware-synthesizer

4
  • 2 layers45.7 × 106.7 mmVCA Module, the printed circuit board in 3D

    VCA Module

    Fora888/fully-digital-modular-hardware-synthesizer

    A digital audio transmission specification for eurorack like modular synthesizers

    51 partsMIT
  • 2 layers53.3 × 106.7 mmADSR Module, the printed circuit board in 3D

    ADSR Module

    Fora888/fully-digital-modular-hardware-synthesizer

    A digital audio transmission specification for eurorack like modular synthesizers

    41 partsMIT
  • 2 layers15.2 × 99.1 mmUSB C 3A PSU, the printed circuit board in 3D

    USB C 3A PSU

    Fora888/fully-digital-modular-hardware-synthesizer

    A digital audio transmission specification for eurorack like modular synthesizers

    34 partsMIT
  • 2 layers55.9 × 101.6 mmWavetableVCO Module, the printed circuit board in 3D

    WavetableVCO Module

    Fora888/fully-digital-modular-hardware-synthesizer

    A digital audio transmission specification for eurorack like modular synthesizers

    34 partsMIT

Similar boards

  • 2 layers55 × 80 mmBoard esp32 v2, the printed circuit board in 3D

    Board esp32 v2

    sudomesh/disaster-radio

    A (paused) work-in-progress long-range, low-bandwidth wireless disaster recovery mesh network powered by the sun.

    101 parts1.1k
  • 2 layers99 × 145.5 mmLamp, the printed circuit board in 3D

    Lamp

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    101 parts915
  • 2 layers230.5 × 60 mmEEZ DIB AUX PS, the printed circuit board in 3D

    EEZ DIB AUX PS

    eez-open/modular-psu

    EEZ Bench Box 3 (BB3) Modular T&M chassis

    101 parts394
  • 2 layers224.6 × 74.2 mmKeyboard ch552-44, the printed circuit board in 3D

    Keyboard ch552-44

    rgoulter/keyboard-labs

    Repo with my PCB designs and keyboard firmware

    101 parts236
  • 2 layers90 × 60 mmCh32v307gigabit, the printed circuit board in 3D

    Ch32v307gigabit

    cnlohr/cnhardware

    My dumping grounds for all my kicad projects and random hardware bringup.

    101 parts114
  • 2 layers450 × 125 mmA1200KB, the printed circuit board in 3D

    A1200KB

    aeberbach/A1200KB

    As of right now this is revision 4. I know it could be improved very, very slightly by changing the position of key groups by less than a millimetre but I think it's complete now.

    101 parts75
  • 2 layers100 × 100 mmLittleSwitchBus, the printed circuit board in 3D

    LittleSwitchBus

    profdc9/ModularTuner

    A Modular Antenna Tuner for a Phased Array Antenna System

    101 parts59

Questions

How big is the USB IO Module PCB?

It measures 55.9 × 106.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the USB IO Module use?

101 parts, built around the SC16IS762IPW. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the USB IO Module KiCad files?

From the Fora888/fully-digital-modular-hardware-synthesizer repository on GitHub, at the commit this page was made from: the board is Teensy/PCB/USB_IOModule/USB_IO_Module.kicad_pcb and its schematic Power Supply/USB-C_3A_PSU/USB-C_3A_PSU.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the USB IO Module design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).