

Doorbot esp32
ESP32 RC522 firmware for interfacing with Nexudus
- Size
- 44.4 × 66 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 3
- Nets
- 39
- Pads
- 50
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 5 (file 20171130)
- Created
- 15 Jun 2020
- Updated
- 11 Apr 2023
Overview
Doorbot esp32 is an open-source printed circuit board by FarsetLabs, from the FarsetLabs/doorbot-esp32 repository on GitHub, published under the MIT licence. It is a 2-layer board of 44.4 × 66 mm with 3 parts on 39 nets.
Its parts include 1 IC, 1 diode and 1 connector. It belongs with the ESP32 boards of this library.
README
README.mddoorbot-esp32
RFID Card Reader and Door Relay Opening Module for use with the doorbot project.
It's general operation is:
- Setup Wi-Fi Connection*
- Setup MFRC522 Card Connection
- Loop waiting for card presence detection
- On Card Detect, Grab the UID from the presented Card
- Attempt to trigger an 'open' action* on the door identified by the onboard device_id, using the same device id and the UID from the presented card as the Username and Password for HTTP Basic Auth
- If 200 response; flash green on RGB LED and unlock door via relay for 5 seconds
- Otherwise flash red for 5 seconds and resume loop
*Configured through build-time environment variables, see platform.ini for details
Hardware Setup
This project uses an ESP-WROOM-32 package, an RC522 RFID module


Pin Mappings:
RC522 -> ESP32
| RC522 | ESP32 | Description |
|---|---|---|
| 3v3 | 3v3 | VIN |
| RST | D22 | Reset |
| GND | GND | Ground |
| IRQ | Unused | |
| MISO | D19 | SPI Master Input |
| MOSI | D23 | SPI Master Output |
| SCK | D18 | SPI Clock |
| SDA | D21 | Serial Data Line |
RGB LED -> ESP32
| RGB LED | ESP32 | Description |
|---|---|---|
| (-) | GND | Ground |
| R | D2 | Red |
| G | D4 | Green |
| B | Blue |
RELAY -> ESP32
| RELAY | ESP32 | |
|---|---|---|
| NO | D15 | Normally Open (Actuator) |
| + | 3v3 | +VE |
| - | GND | Ground |
Parts
3| Qty | Value | Footprint | References |
|---|---|---|---|
| 1 | ESP32-DEVKITC-32D | board:MODULE_ESP32-DEVKITC-32D | U1 |
| 1 | LED_ARBG | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | D1 |
| 1 | RFID-RC522 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J1 |
Similar boards
- 2 layers40 × 30 mm

- 2 layers51.9 × 16 mm

Passive2-rpi non standard adapter
hzeller/rpi-rgb-led-matrix
Controlling up to three chains of 64x64, 32x32, 16x32 or similar RGB LED displays using Raspberry Pi GPIO
3 parts4.4kGPL-2.0 - 2 layers16.3 × 16.3 mm

- 2 layers

Sub
atopile/atopile
Design circuit boards with code! ✨ Get software-like design reuse 🚀, validation, version control and collaboration in hardware; starting with electronics ⚡️
3 parts4kMIT - 2 layers85 × 30 mm

- 2 layers124.5 × 33.7 mm

- 2 layers10.5 × 83 mm

- 2 layers21.2 × 51.3 mm

Pico reset
hackclub/sprig
🍃 Learn to code by making games in a JavaScript web-based game editor.
3 parts1.1kMIT
Questions
How big is the Doorbot esp32 PCB?
It measures 44.4 × 66 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Doorbot esp32 use?
3 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Doorbot esp32 KiCad files?
From the FarsetLabs/doorbot-esp32 repository on GitHub, at the commit this page was made from: the board is board/board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Doorbot esp32 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).