Skip to the content
2 layers100 × 135 mmRotor, the printed circuit board in 3D

Yet another K3NG rotator controler pcb

Size
100 × 135 mm
Copper layers
2
Thickness
1.6 mm
Parts
60
Nets
91
Pads
275
Tracks, vias
436, 38
Pours
9
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
13 Jan 2024
Updated
13 Nov 2024

Overview

Rotor is an open-source printed circuit board by F6ITU, from the F6ITU/K3NG_rotor repository on GitHub. It is a 2-layer board of 100 × 135 mm with 60 parts on 91 nets, routed with 436 tracks and 38 vias.

Its parts include 33 connectors, 8 capacitors, 2 resistors and 1 IC.

README

README.md

K3NG_rotor

Yet another K3NG rotator controler pcb

This implementation is based on an Arduino Mega board and a pair of 4x relay boards to drive an AZ-EL antenna system.

Most basic functions are directly driven via Molex KK 254 connectors (up/down, right/left, lcd display output, GPS input, * I2C extensions... etc). All other "vacant" gpio could be used via solderpads.

Board could be powered from 8 to 15V

Source code and wiki should be downloaded at

https://github.com/k3ng/k3ng_rotator_controller

K3NG rotator, component side

K3NG rotator, bottom side

Notes de montage

  • Les barrettes de contact au pas de 2,54 doivent être soudées après les avoir insérées dans les connecteur gpio de l’Arduino. La série de brasure doit donc être effectuée avec le module MCU en place, lequel servira ainsi de gabarit d’alignement pour les broches. Sans cette précaution, il sera quasiment impossible d’installer l’Arduino sur la carte.

  • Le régulateur de tension doit être le circuit à souder avant tout autre composant. Les deux principaux condensateurs de filtrage sont très proche du 7805 et gêneraient la brasure ce celui-ci s’il était monté a posteriori

  • Tous les connecteurs Molex kk254 ne sont pas nécessairement à installer. C’est le cas notamment des entrées gpio « serial » de 0 à 3, qui peuvent être remplacés par de simples jumpers les reliant aux sorties des périphériques installés. Cela permet de choisir sur quel port seront reliés les modules gps ou Nextion s’il y a lieu

  • Toutes les E/S de l’Arduino sont doublées par une rangée de contacts au pas de 2,54, laissant libre toute possibilité d’ajouts de modules exotiques.

  • Les modules « 4 relais » disponibles sur Amazon ou AliExpress sont généralement livrés avec un connecteur « broches carte à fils » au pas de 2,54mm orientés vers le dessus de la carte. Il est nécessaire de les dessouder et de les remplacer par un connecteur identique, mais soudé « coté piste ». Le shield K3NG doit, pour sa part, être équipé d’un connecteur femelle « carte à carte » pour recevoir la ou les cartes relais en « piggy back ».

  • Deux cartes relais peuvent être installées pour piloter une paire de moteurs azimut/élévation. Prévoir deux entretoises d’une hauteur équivalente aux connecteurs de liaison.

  • ATTENTION : les relais sont commandés « 2 à 2 », soit pour assurer une coupure courants forts, soit pour être utilisés en inverseur (un contact ouvert et un contact fermé au repos, et lycée de Versailles au travail). Cette configuration est notamment nécessaire pour commander les rotor Kantronic/Yaesu/Toyomura d’ancienne génération (split phase ou à phase divisée)

  • Une BOM interactive est disponible sur ce Github dans le répertoire BOM du même métal

Parts

60
QtyValueFootprintReferences
6Conn_01x02Connector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ17, J19, J29, J31, J34, J36
6MountingHole_3.2mmArduino_MountingHole:MountingHole_3.2mmMH1, MH2, MH3, MH4, MH5, MH6
410nCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC1, C2, C3, C5
4MountingHole_PadMountingHole:MountingHole_3.5mm_PadH1, H2, H3, H4
2100nCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC4, C6
2100uCapacitor_SMD:CP_Elec_10x12.6C7, C8
21kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR2, R3
2AnalogConnector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_VerticalJ3, J8
2AnalogConnector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_VerticalJ5, J10
2CommunicationConnector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_VerticalJ6, J11
2Conn_01x16Connector_PinHeader_2.54mm:PinHeader_1x16_P2.54mm_VerticalJ14, J15
2PWMConnector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_VerticalJ4, J13
2PWMConnector_PinSocket_2.54mm:PinSocket_1x10_P2.54mm_VerticalJ2, J12
2PowerConnector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_VerticalJ1, J9
14k7Potentiometer_SMD:Potentiometer_Bourns_TC33X_VerticalRV1
1AZ_RelayConnector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_VerticalJ26
1Conn_01x04Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_VerticalJ21
1DigitalConnector_PinSocket_2.54mm:PinSocket_2x18_P2.54mm_VerticalJ7
1EL_RelayConnector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_VerticalJ16
1GPS Neo7MConnector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_VerticalJ35
1LCD 4x16 I2CConnector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_VerticalJ33
1LCD 4x16//Connector_Molex:Molex_KK-254_AE-6410-16A_1x16_P2.54mm_VerticalJ20
1LOGOLicht:lichtensteinG***
1NextionConnector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_VerticalJ30
1Push_button_CCWConnector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ23
1Push_button_CWConnector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ22
1Push_button_DwNConnector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ25
1Push_button_UPConnector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ24
1XT30 connectorConnector_AMASS:AMASS_XT30U-F_1x02_P5.0mm_VerticalJ37
1uA7805Package_TO_SOT_SMD:TO-263-3_TabPin2U1

The 56 most common of 60 parts.

Similar boards

  • 2 layers35 × 50 mmGoblin, the printed circuit board in 3D

    Goblin

    kelu124/echomods

    Open source ultrasound processing modules and building blocks

    60 parts463
  • 2 layers32.9 × 119.1 mmConnector, the printed circuit board in 3D

    Connector

    thpoll83/PolyKybd

    PolyKybd

    60 parts411CERN-OHL-W-2.0
  • 2 layers35.9 × 62.7 mmRp2040-memcard, the printed circuit board in 3D

    Rp2040-memcard

    sd2psx/pcb

    The PCB must be produced in 0.8mm thickness. Production files are provided under the "Releases" tab. These do not include the through-hole OLED module.

    60 parts241
  • 2 layers58 × 110 mmBrain ui split pulse, the printed circuit board in 3D

    Brain ui split pulse

    shmoergh/moduleur

    Fully analog DIY-friendly modular synth

    60 parts222
  • 2 layers52 × 90 mmEmu brd, the printed circuit board in 3D

    Emu brd

    rscott2049/DECstation2040

    A RP2040 based DECstation emulator

    60 parts212BSD-3-Clause
  • 2 layers42.5 × 80 mmSimplemixsmall, the printed circuit board in 3D

    Simplemixsmall

    nickajeglin/Eurorack-pcbs

    A collection of easy to solder DIY eurorack PCB's

    60 parts208
  • 2 layers57.4 × 12 mmZicada, the printed circuit board in 3D

    Zicada

    CoretechR/Zicada

    DIY Zigbee Multisensor

    60 parts205GPL-3.0
  • 2 layers87.9 × 123.9 mmBitdoglab, the printed circuit board in 3D

    Bitdoglab

    BitDogLab/BitDogLab

    Open-source educational hardware for embedded systems, programming, electronics, and physical computing.

    60 parts203

Questions

How big is the Rotor PCB?

It measures 100 × 135 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Rotor use?

60 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Rotor KiCad files?

From the F6ITU/K3NG_rotor repository on GitHub, at the commit this page was made from: the board is rotor.kicad_pcb and its schematic rotor.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Rotor design in my own project?

Its repository states no licence, so its author keeps all rights: ask F6ITU before reusing the design.