

Porsche quad gauge
A custom built quad gauge for a Porsche 914 using new and salvaged components.
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 57
- Nets
- 56
- Pads
- 188
- Tracks, vias
- 522, 42
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 14 Dec 2020
- Updated
- 15 Dec 2020
Overview
Porsche quad gauge is an open-source printed circuit board by Evancli, from the Evancli/porsche-quad-gauge repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 2-layer board with 57 parts on 56 nets, routed with 522 tracks and 42 vias.
It is built around the L4941BDT-TR, TLP290-4(E and WS2812B. Its parts include 13 resistors, 12 diodes, 7 capacitors, 3 ICs and 2 connectors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
3L4941BDT-TR
DPAK-40℃~+150℃@(Tj) 1 16V 1A 30uV 4mA 5V 700mV@(1A) 89dB@(120Hz) Fixed Positive Reverse connection protection、Short Circuit Protection、Thermal Shutdown DPAK Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTLP290-4(E
SOP-16-55℃~+110℃ 1.2V 2.5kV 2ns 3ns 4 400% 400mV@2.4mA,8mA 50% 50mA 50mA 80V DC Phototransistor SOP-16 Transistor, Photovoltaic Output Optoisolators ROHSToshibaTransistor, Photovoltaic Output OptoisolatorsWS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorised
README
README.md
QUAD GAUGE FOR A PORSCHE 914
More info here.
Required Items
This gauge uses salvaged components from a Porsche 944 fuel gauge; the bezel, glass, and face plate. You can used the vintage gauges from the 944 or the corresponding gauges from your 914. It also required two new VDO gauges for voltage and oil pressure.
Disassembly Tips
It's quite laborious to open these VDO gauges, even with the right tools. A prying spudger and flat implement are needed. Lots of care and attention to not mess up the sheet metal. Be very careful when you pry open the 944 fuel gauge. It's very easy damage the surface finish of the bezel.
Processes
The build uses 3D printed parts as well a laser cut and etched parts.
License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Parts
57| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | WS2812B | Porsche Quad Gauge:WS2812B | D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12 |
| 11 | CONNECTOR_QC_TAB_0.25 | Porsche Quad Gauge:CONNECTOR_QC_TAB-0.25 | 12V1, ALTERNATOR1, BRAKE_GND1, COOLANT_TEMP1, FLASHER1, FUEL_LOW1, FUEL1, GND1, LIGHT1, OIL_LOW1, OIL_PRESSURE1 |
| 6 | 10uF | Porsche Quad Gauge:0805 | C1, C2, C3, C4, C5, C6 |
| 4 | @HOLE0, @HOLE1, @HOLE2, @HOLE3 | ||
| 4 | 1.2K | Porsche Quad Gauge:0805 | R1, R2, R3, R4 |
| 4 | 392 | Porsche Quad Gauge:0805 | R10, R11, R12, R13 |
| 3 | 1k | Porsche Quad Gauge:0805 | R5, R6, R7 |
| 2 | VDO_NEW | Porsche Quad Gauge:VDO_NEW_GAUGE_SOCKET | OIL_PRESSURE_GAUGE1, VOLTAGE_GAUGE1 |
| 2 | VDO_OLD | Porsche Quad Gauge:VDO_GAUGE_SOCKET | COOLANT_TEMP_GAUGE1, FUEL_GAUGE1 |
| 1 | 0.1uF | Porsche Quad Gauge:0805 | C7 |
| 1 | 10K | Porsche Quad Gauge:0805 | R8 |
| 1 | 1M | Porsche Quad Gauge:0805 | R9 |
| 1 | ATMEGA328P_TQFP | Porsche Quad Gauge:TQFP32-08 | U1 |
| 1 | AVR_SPI_PROG_3X2TESTPOINTS | Porsche Quad Gauge:2X3_TEST_POINTS | J1 |
| 1 | CONN_02 | Porsche Quad Gauge:1X02 | J2 |
| 1 | L4941BDT-TR | Porsche Quad Gauge:D-PAK_TO252AA | U3 |
| 1 | PRQC16.00SR1010V00L | Porsche Quad Gauge:3-SMD | OSC1 |
| 1 | TLP290-4 | Porsche Quad Gauge:SO16 | U2 |
Similar boards
- 4 layers137 × 86 mm

- 4 layers58 × 38 mm

Qspimux2-prog
felixheld/qspimux
QSPI flash multiplexer - connect a SPI NOR flash to either an embedded system or a programmer for remote firmware tests
99 parts57CC-BY-SA-4.0 - 4 layers76 × 82.5 mm

Nucleo64 CNC
terjeio/CNC_Breakout_Nucleo64
CNC breakout for STM324F411 and ST32F446 development boards
120 parts22 - 4 layers58.4 × 62.5 mm

CNC Boosterpack
terjeio/CNC_Boosterpack
A BoosterPack that provides 3-axis motor support for some TI LaunchPads
74 parts13 - 2 layers92.8 × 133.8 mm

ElectromagnetController V5
brooklynresearch/FerrousControl
Ferrofluid controlled through an electromagnetic array
108 parts2 - 2 layers388 × 444 mm

- 4 layers240 × 180 mm

- 2 layers100 × 100 mm

Questions
What parts does the Porsche quad gauge use?
57 parts, built around the L4941BDT-TR, TLP290-4(E and WS2812B. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Porsche quad gauge KiCad files?
From the Evancli/porsche-quad-gauge repository on GitHub, at the commit this page was made from: the board is PCB/KiCad/Porsche Quad Gauge.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Porsche quad gauge design in my own project?
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
