Skip to the content
2 layers42.8 × 122.5 mmFBT, the printed circuit board in 3D

Full body tracking modules

Size
42.8 × 122.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
23
Nets
45
Pads
112
Tracks, vias
219, 12
Pours
3
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
10 Jun 2025
Updated
21 Jul 2026

Overview

FBT is an open-source printed circuit board by DrGlaucous, from the DrGlaucous/UFBTM repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 42.8 × 122.5 mm with 23 parts on 45 nets, routed with 219 tracks and 12 vias.

Its parts include 2 resistors, 2 connectors, 1 capacitor, 1 IC and 1 switch.

README

Readme.md

UFBTM

Unnamed Full Body Tracking modules

They have a name now...

Mr. Tracker

A cheap, compact, and open-source realtime tracking module built with slimeVR and the ESP32.

Design goal

Details

The components for these trackers have been chosen to be exclusively through-hole for ease of assembly (at a slight cost of a larger size)

The main IMU this design is based around is the BMI160, primarily for its low cost and small breakout footprint. This IMU is notorious for drifting, so it is also paired with a GY-271 magnetometer to mitigate some of the drift (depending on use location, the magnetometers may need to be disabled due to poor magnetic field).

This idea is by no means novel; I'm not even the first person to use the components I'm using, but I'm attempting to take a cost approach here. The full tracking set (10 modules + 5 extenders) can potentially be as low as $100 USD without print time costs or filament prices.

Assembly should be quick and reliable with no need for SMD or rework, which is something other modules of this size can't do.

The module uses TRRS (4 ring) aux jacks to connect between the main board and its extender, providing a robust connection that can last many plug cycles and be easily replaced if the wire goes bad.

Battery life of these trackers should be comparable to official ESP8266-based slime trackers, though I've only personally used them for about 6-8 hours at a time.

Compatibility

MCU

MCU

For the microcontroller, this board can support anything with the "superMini" form factor with the 8 or 9 pin length (including the s3 variants, though I haven't tested the firmware with the s3)

[!NOTE] Check to make sure the +5v, GND, and +3.3v on the board match the "standard" superMini layout as seen above! Some boards like to mix them around, like the one below. That one WILL NOT WORK.

Note how the power pins are on the opposite side from the normal superMini board

My preference is the variant commonly labeled as "Pro Minis" or "C3 Minis" because the normal "Supermini" modules can have issues with antenna reception, depending on which ones you get. (and it's a mixed bag, so you're never really sure if you're getting the right ones)

The "Pro Mini" modules have a larger antenna that seems further spaced from the rest of the components. They're distinct enough that you always know you're getting the right type of board, and as far as I can tell, haven't been complained about online. They also have a place for an external antenna, should you ever want to go that route. SuperMini v2 modules also work well, but are typically more expensive.

An example of an "ESP32 C3 pro mini"

IMU

IMU

The IMU can be anything that matches the BMI160 breakout form-factor. This includes:

  • The BMI160 itself
  • The LSM6DS3 (note: getting these from AliExpress will often just get you a re-badged BMI160.) These aren't officially supported by the upstream slimeVR firmware as-of-writing, but are supported by my custom fork.
  • Slimevr "Mumo" boards hosting a CM-45686 module
  • Mofflab LSM6DSV modules (I'm sure there are other vendors of these that I haven't mentioned, but these are all I could find while searching the internet. Join the SVR discord if you want to find better sources)

Magnetometer

Magnetometer

The PCB was designed to hold a GY-271 magnetometer breakout board. These boards are common enough, but tend to have several variants of actual magnetometer on them, including:

  • HMC5883L
  • QMC5883L
  • QMC5883P

All these are supported by my fork of the slimeVR firmware (with the BMI160 and LSM6DS3, I haven't tested with the mumos or mofflab boards, but if the IMU on those are good enough, you shouldn't need a magnetometer anyway), but they have distinct registers, so you will have to check which one you have. (as-of-writing, the QMC5883P is the most common of these)


Charger

Charger

One of the most compact jellybean chargers are the LX-LBES chargers. They tend to come in 2 distinct sizes, and it's unreliable which one you might get. The PCB can support either of them though, so this shouldn't be a problem. These are also commonly labeled as TP4057 charger boards.

Just make sure it's the LX-LBES module and not the other variants like the LX-MILC or LX-LBC3, both of which are similarly sized, but are incompatible.

On the left: the smaller of the two LX-LBES boards, on the right: the more common larger variant. Both of these will work for these trackers

Battery

Battery

This tracker is designed to work with 2 distinct battery sizes:

  • The 804040 (a square flat-pack, used with Mr. Tracker PCBs)
  • The 18650 (a common cylindrical battery, used with Mrs. Tracker PCBs)

Unfortunately, I have not modeled a housing for the 18650 variant yet.

18650 batteries are cheaper than the 804040s, especially if you get them used from a place like batteryhookup, where they cost about 50c per battery. Depending on the quality of the cell, they can also hold more charge than the 804040s, but as a trade-off are inconveniently shaped for trackers. The Mrs. Tracker PCB is designed to accommodate these long, skinny batteries as best as possible.


LDO

LDO

The LDO regulates the incoming battery voltage down to 3.3 volts for the electronics. The board will accept any LDO in a TO-92 package, but was designed around the HT7333 regulator as that is what I could get off Amazon.

If the LDO you select has a different pinout than the HT7333, then you will need to reconfigure the jumpers as described in Power configuration.

This part is optional if your IMU has a built-in 5v to 3.3v regulator that can support the currents required by the ESP32 and other componets. I've seen some that both could and couldn't, so I'd assume the worst case and use a discrete LDO for safety.

The MCP1700 also shares the same pinout and is rated at 250mA.

Capacitor requirements

Many of these LDOs require an inline capacitor for voltage smoothing and stable output (for example, the datasheet for the MCP1700 regulator says it requires at least a 1uf capacitor). I was able to find 10uf ceramic capacitors to use in my design, but you may be able to get away with smaller values, or even none at all. The HT7333 worked without a capacitor too, but it would have trouble slightly sooner than with a capacitor when the battery voltage got too low.

Bill of Materials

Prices are generally cheaper if you buy in bulk from China, which is recommended since you'll likely be building at least five of these and need to order the PCBs from there anyway. (unless you have to use a domestic PCB manufacturer, in which case you'll probably end up paying several times more than ordering through a provider like JLCPCB) Most of this stuff should be available to get on Amazon as well, albeit more expensive.

I've added some links to the BOMs below to help new builders get started, but there might be better deals for the same parts with some shopping around, which I encourage you to do.

[!NOTE] Some of the links below have multiple options on the listing (like the resistors for instance. Make sure you choose the correct type!)

Mr/Mrs. Tracker part list


partqty per trackerqty per package (typical)price per package (typical, USD)Link (non-affiliate, U.S. domain, may be expired)
PCB (ordered from PCB provider)15-20~$10 excluding shippingJLCPCB
ESP32 C3 (see compatible devices)11~$2.5AliExpress
IMU (see compatible devices)11~$2.5AliExpress
GY-271 Magnetometer (see compatible devices) (optional, but recommended to limit drift)11~$2AliExpress
LX-LBES li-ion charger (see compatible devices)15-10~$5AliExpress
3.3v LDO (see compatible devices)120-100~$3AliExpress
10uF Ceramic Capacitor (maybe optional, see LDO)1100~$3AliExpress
200K resistor (for voltmeter)2100~$2AliExpress
On-Off Switch (SK12D07VG4)1100~$2AliExpress
TRRS Connector (PJ-320A) (Optional, for extenders)120~$2AliExpress
M2.5x6 self tapping screws550~$2AliExpress, Amazon
804040 battery15~$18 USDAliExpress
Elastic straps, 25mm wideVaries5 Meters~$4AliExpress
Strap Buckles, 25mm wide15~$5AliExpress
Sewing thread for attaching buckles to strapsVariesVariesN.A.N.A.
Plastic housing1N.A.N.A.N.A.

Extender (Tracker Jr) part list


partqty per trackerqty per package (typical)price per package (typical, USD)Link (non-affiliate, U.S. domain, may be expired)
PCB (ordered from PCB provider)15-20~$10 excluding shippingJLCPCB
IMU (see compatible devices)11~$2.5AliExpress
GY-271 Magnetometer (see compatible devices) (optional, but recommended to limit drift)11~$2AliExpress
TRRS Connector (PJ-320A)120$2AliExpress
TRRS Male-Male Aux cable, 1 meter11$2AliExpress
Elastic straps, 25mm wideVaries5 Meters$4AliExpress
Strap Buckles, 25mm wide15~$5AliExpress
Sewing thread for attaching buckles to strapsVariesVariesN.A.N.A.
Plastic housing1N.A.N.A.N.A.

Power configuration

Details

Rev. 3 boards have several jumpers on the underside that changes how the device can be powered so a wider range of parts can be used.

Depending on the quality of the IMU breakout board, the linear regulator and voltage smoothing capacitor may not be needed. This varies more than you'd think with distributors though, so it's not always safe to count on it. Additionally, some versions of the IMU breakout might not even have an integrated regulator at all, making the discrete regulator required.

  • Jumpers A, B, C, and D alter the pinout for the voltage regulator and allow one with any pin arrangement to be installed.
  • Connecting jumper E allows the board to use the voltage regulator on the IMU instead of the discrete one.
  • Connecting jumper F allows the ESP32's USB port to charge the battery. The drawback is that charging the tracker will always turn on the ESP32, wasting power and charging slower.

The following is a table of all the possible voltage regulator pinouts and their corresponding jumper configs. An "O" means to leave the jumper at default (bridging positions 1 and 2), an "X" means to cut the jumper and flip it (bridging positions 2 and 3). "Flip" means to solder the regulator into the socket backwards

[!NOTE] Although I tried to keep the ABCD jumpers next to each other, their orientations are flipped! Pay close mind to what side of the jumper pad the "1" and "3" are on in the silkscreen!

PinoutABCDFlip
OOOOO
OOXXO
XXOOO
XXOOX
OOXXX
OOOOX

In a nutshell,

  • AB flip 1 and 2,
  • CD flip 2 and 3

image

[!CAUTION] Everything below this point is very unfinished (as opposed to only slightly unfinished, as is seen above)

Ordering PCBs

todo: this

Recommended tools for assembly

In theory, these trackers can be assembled just fine with a Wal-Mart special (link included for meme purposes only!) soldering iron, a pair of children's safety scissors, a manicure file, and a sewing needle. Will you have a good time doing it? No, but it's definitely possible.

Instead of that, here's the list of tools I recommend to make assembly of these go smoothly:

  • A Soldering Iron (the Wal-Mart special will work, but I suggest getting something at least partway decent on Amazon; good soldering irons can be had for less than $30.)
  • Solder (lead solder is easier to work with, but lead-free works OK too if you're cautious about working with lead.)
  • Flush cutters
  • A needle file set (optional)
  • SMD Tweezers
  • Helping hands vice (optional)
  • Small phillips screwdriver (for the screws on the housing)

For the straps:

  • A pair of scissors (preferably not child safety ones)
  • A lighter
  • A sewing needle or sewing machine
  • Sewing thread

Assembly Preface

These guides assume you have everything in hand required to build one of these trackers.

Typically, a good rule of thumb is to start with the lowest profile components first and work your way up by height. Most of the stuff on these trackers is the same height however, so order isn't ultra-important; nothing really gets in the way of anything else, but regardless, I still like to start with the breakout boards (MCU, IMU, Magnetometer, and Charger).

To keep the tracker as compact as possible, the breakouts are soldered directly on top of the board. This makes them much more difficult to remove though, so be careful during assembly!

I've had an IMU come to me dead on arrival and had to go through the painstaking process of desoldering it from the board. (which involved simultaneously heating the pins and wedging an xacto between the IMU and the PCB) Because of that, I like to make sure that parts work beforehand by soldering up a test rig with removable pins to test parts with.

Working with a breadboard for testing is feasible too, but it's less likely that people would just have one of those onhand, much less the desire to wire an entire setup just to see if a few parts maybe don't work.

Assembly (Mr. Tracker)

Details

Assembly (Mrs. Tracker)

Assembly (Tracker Jr)

Parts

23
QtyValueFootprintReferences
2200KResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1, R2
2TRRS Connector 3.5My_Library:PJ-320AJ1, J2
2~My_Library:GY-BMI160IMU1, IMU2
2~My_Library:GY-271GY1, GY2
110 uFCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC1
1AJumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_NumberLabelsJP3
1BJumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_NumberLabelsJP5
1BatteryConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalBT1
1Battery anodeConnector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_VerticalBT-2
1CJumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_NumberLabelsJP6
1DJumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_NumberLabelsJP4
1EJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP1
1FJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP2
1HT7333-1-TO92Package_TO_SOT_THT:TO-92L_InlineU1
1SW_SPDTMy_Library:SK12D07VG4SW1
1~My_Library:LX-LBES-BigCHGR2
1~My_Library:LX_LBESCHGR1
1~Espressif:ESP32-C3-SuperMini_PLUSMCU1

The 22 most common of 23 parts.

More from DrGlaucous/UFBTM

7
  • 2 layers40 × 40 mmFBT, the printed circuit board in 3D

    FBT

    DrGlaucous/UFBTM

    Full body tracking modules

    19 partsGPL-3.0
  • 2 layers53.9 × 82.8 mmFBT, the printed circuit board in 3D

    FBT

    DrGlaucous/UFBTM

    Full body tracking modules

    18 partsGPL-3.0
  • 2 layers40 × 40 mmFBT, the printed circuit board in 3D

    FBT

    DrGlaucous/UFBTM

    Full body tracking modules

    15 partsGPL-3.0
  • 2 layers21 × 65.4 mmFBT, the printed circuit board in 3D

    FBT

    DrGlaucous/UFBTM

    Full body tracking modules

    15 partsGPL-3.0
  • 2 layers40 × 40 mmFBT, the printed circuit board in 3D

    FBT

    DrGlaucous/UFBTM

    Full body tracking modules

    14 partsGPL-3.0
  • 2 layers20 × 65 mmFBT, the printed circuit board in 3D

    FBT

    DrGlaucous/UFBTM

    Full body tracking modules

    14 partsGPL-3.0
  • 2 layers18.5 × 23.1 mmFBT, the printed circuit board in 3D

    FBT

    DrGlaucous/UFBTM

    Full body tracking modules

    3 partsGPL-3.0

Similar boards

  • 2 layers65 × 56 mmPi servo hat, the printed circuit board in 3D

    Pi servo hat

    earthtojake/text-to-cad

    Design physical products with AI

    23 parts26kMIT
  • 2 layers14 × 100 mmYunomi, the printed circuit board in 3D

    Yunomi

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    23 parts3kApache-2.0
  • 2 layers50.8 × 52.2 mmFuhhni, the printed circuit board in 3D

    Fuhhni

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    23 parts915
  • 2 layers138.8 × 89.8 mmKeyboard pcb, the printed circuit board in 3D

    Keyboard pcb

    diepala/cantor

    Cantor keyboard, a 42 key diodeless split keyboard.

    23 parts756GPL-3.0
  • 2 layers32.9 × 53.3 mmGoatgdo, the printed circuit board in 3D

    Goatgdo

    Kaldek/rat-ratgdo

    Open source schematics for ratgdo PCB

    23 parts511MIT
  • 2 layers35.5 × 50 mmTobo, the printed circuit board in 3D

    Tobo

    kelu124/echomods

    Open source ultrasound processing modules and building blocks

    23 parts463
  • 2 layers19 × 19 mmKeybit, the printed circuit board in 3D

    Keybit

    notaroomba/keybytes

    A truly modular keyboard

    23 parts444
  • 2 layers88.5 × 28 mmExpBreakout, the printed circuit board in 3D

    ExpBreakout

    Duet3D/Duet-2-Hardware

    The KiCAD source for the Duet 3d printer controller see www.duet3d.com

    23 parts258

Questions

How big is the FBT PCB?

It measures 42.8 × 122.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the FBT use?

23 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the FBT KiCad files?

From the DrGlaucous/UFBTM repository on GitHub, at the commit this page was made from: the board is Schematic/Batt_18650/FBT.kicad_pcb and its schematic Schematic/Batt_18650/FBT.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the FBT design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).