Skip to the content
2 layers50 × 50 mmADVAITH PCB, the printed circuit board in 3D

WHAT THE ARDUINO DOES ---------------------- The Arduino acts as the brain of the electronic dice. It waits for a button press, generates a random number from 1 to 6, and lights up the correct LEDs to show that number…

Size
50 × 50 mm
Copper layers
2
Thickness
1.6 mm
Parts
21
Nets
36
Pads
68
Tracks, vias
65, 1
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
23 May 2026
Updated
23 May 2026

Overview

ADVAITH PCB is an open-source printed circuit board by Djmassi0101, from the Djmassi0101/PCB-Design repository on GitHub. It is a 2-layer board of 50 × 50 mm with 21 parts on 36 nets, routed with 65 tracks and 1 via.

Its parts include 7 resistors, 7 diodes, 1 connector and 1 switch. It belongs with the AVR (ATmega, ATtiny) boards of this library.

README

README.md

PCB-Design

ELECTRONIC DICE – MICROCONTROLLER I/O EXPLANATION

WHAT THE ARDUINO DOES

The Arduino acts as the brain of the electronic dice. It waits for a button press, generates a random number from 1 to 6, and lights up the correct LEDs to show that number as a dice face.

INPUTS TO THE ARDUINO

Push Button (1 digital input pin): The button is wired between a digital input pin and ground. When not pressed, the pin reads HIGH (held up by the Arduino's internal pull-up resistor). When pressed, it gets pulled to ground and reads LOW. The Arduino detects this LOW signal as a button press event.

OUTPUTS FROM THE ARDUINO

LED Control (7 digital output pins): A standard dice face uses up to 7 LED positions arranged in a grid. Each LED position is driven by one output pin through a current-limiting resistor. The Arduino sets the relevant pins HIGH to turn LEDs on and LOW to turn them off.

The 7 positions map to each dice face like this:

Dice Face 1 -> Center only Dice Face 2 -> Top-right, Bottom-left Dice Face 3 -> Top-right, Center, Bottom-left Dice Face 4 -> All 4 corners Dice Face 5 -> All 4 corners + Center Dice Face 6 -> All 4 corners + Left-middle + Right-middle

HOW IT WORKS (STEP BY STEP)

  1. Arduino powers on and sets all LED pins LOW (all off)
  2. It continuously watches the button input pin
  3. When a button press is detected (pin goes LOW), it triggers a random number routine
  4. The Arduino picks a number between 1 and 6 using a random seed
  5. It looks up which LED positions correspond to that number
  6. It sets those output pins HIGH, lighting the correct LEDs
  7. After a short display time, it resets and waits for the next press

RESISTOR CALCULATION

Formula: R = (Vcc - Vf) / I

R = (5V - 2V) / 0.015A R = 3V / 0.015A R = 200 Ohms

Each LED gets a 200 Ohm resistor in series to safely limit current to 15mA.

Parts

21
QtyValueFootprintReferences
7LEDLED_THT:LED_D5.0mmD1, D2, D3, D4, D5, D6, D7
5RResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR3, R4, R5, R6, R7
2200Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1, R2
1Arduino_Nano_v3.xModule:Arduino_NanoA1
1Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_HorizontalJ1
1SW_PushButton_Switch_THT:SW_PUSH_6mmSW1

The 17 most common of 21 parts.

Similar boards

  • 2 layers28.3 × 39.8 mmLevelShifter, the printed circuit board in 3D

    LevelShifter

    gusmanb/logicanalyzer

    24 channel, 100Msps logic analyzer hardware and software

    21 parts5.1kGPL-3.0
  • 2 layers171.2 × 72.9 mmAmiga gfxcard before pour, the printed circuit board in 3D

    Amiga gfxcard before pour

    mntmn/amiga2000-gfxcard

    MNT VA2000, an Open Source Amiga 2/3/4000 Graphics Card (Zorro II/III), written in Verilog

    21 parts1k
  • 2 layers93.9 × 46 mmRectifier, the printed circuit board in 3D

    Rectifier

    rene-dev/stmbl

    AC Servo Driver for STM32F4

    21 parts990GPL-3.0
  • 2 layers45.5 × 42.9 mmEsphome han reader, the printed circuit board in 3D

    Esphome han reader

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    21 parts915
  • 2 layers31.8 × 14.5 mmEsp prog, the printed circuit board in 3D

    Esp prog

    drandyhaas/KiCadRoutingTools

    A set of Python/Rust tools to aid routing in KiCad

    21 parts744MIT
  • 2 layers23.5 × 15.8 mmQuiverAttachPCB, the printed circuit board in 3D

    QuiverAttachPCB

    Arrow-air/project-quiver

    Project Quiver documentation, designs, and project artifacts.

    21 parts617CERN-OHL-S-2.0
  • 2 layers69.9 × 41.3 mmHeaterMeterLCD, the printed circuit board in 3D

    HeaterMeterLCD

    CapnBry/HeaterMeter

    HeaterMeter and LinkMeter Arduino BBQ Controller

    21 parts557MIT
  • 2 layers161.3 × 111.8 mmDoj, the printed circuit board in 3D

    Doj

    kelu124/echomods

    Open source ultrasound processing modules and building blocks

    21 parts463

Questions

How big is the ADVAITH PCB PCB?

It measures 50 × 50 mm and has 2 copper layers, 1.6 mm thick.

What parts does the ADVAITH PCB use?

21 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ADVAITH PCB KiCad files?

From the Djmassi0101/PCB-Design repository on GitHub, at the commit this page was made from: the board is ADVAITH_PCB.kicad_pcb and its schematic ADVAITH_PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the ADVAITH PCB design in my own project?

Its repository states no licence, so its author keeps all rights: ask Djmassi0101 before reusing the design.