Skip to the content
2 layers143 × 75.5 mmEDMX, the printed circuit board in 3D

This is a custom DMX Tranciver Platform Designed for both reciving and controling DMX. Using an ESP32-C3 With Onboard WIFI

Size
143 × 75.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
19
Nets
23
Pads
85
Tracks, vias
102, 1
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
15 Jul 2025
Updated
27 Jul 2025

Overview

EDMX is an open-source printed circuit board by Darbyshire64, from the Darbyshire64/EndevourDMX repository on GitHub, published under the MIT licence. It is a 2-layer board of 143 × 75.5 mm with 19 parts on 23 nets, routed with 102 tracks and 1 via.

It is built around the MAX485ED. Its parts include 6 diodes, 5 resistors, 3 connectors, 2 ICs and 1 transistor. It belongs with the radio and wireless boards and the ESP32 and RISC-V boards of this library.

Main components

1

README

README.md

EndevourDMX

This is a custom DMX Tranciver Platform Designed for both reciving and controling DMX. Using an ESP32-C3 With Onboard WIFI

[!Warning] Use This PCB at your own Risk. I cannot take liability if it breake's and or causes damage to equipment. This has not been tested and there is no garrentee of upholding to any level of quality/functionality.

https://github.com/user-attachments/assets/77d9e712-4af0-4d90-8f60-33b776832eaa

Curently Availible Firmware Modes

  • Cable Tester
  • Light Controler

Goals

  • Control One DMX Universe
  • Recive DMX and make signal qaulity Reports.
  • WIFI Based Control.
  • Display Status and Other INFO With Inbuilt OLED

How It Works

It allows for DMX Passthrough so if something where to hapen to the MCU the DMX signal Could still passthrough pasiveley without power. The A,B Data lines are protected by a TVS Diode and 100 ohm resistors this cleans up any interfearence in the transmision. this is then sent the the MAX845E Chip to convert the data into easy to recive serieal data for the ESP. As the DMX lighting protocol uses RS845 Serieal the MAX845E is neccesary to control TX/RX the signal.

Photos

PCB

image image

Case

image image

BOM

I know this BOM is Expensive But its cheaper than the equivlent device i was trying to redesign but better, Called MyDMX 3.0 witch is 401.74 USD

LINK

QTYItemPriceLink
PCB Total$14.59
Component Total$38.81
Case Total$4.50
Misc Total$13.36
Total$71.27

PCB

QTYItemPriceLink
5Custom Blue LF HASL PCB$9.40
Shipping (GSDL)$5.19
Total$14.59

Components

I have chosen Digikey because it has all of my components vs LCSC who has a few of my components in stock as of making the BOM. it would be more cost effective to buy all the components in one go rather than by two lots of shipping and handeling fees. and A OLEDs components are cheaper via Ali Express.

Digikey

QTYItemPriceLink
21.5KE15CA$0.34LINK
11N4007$0.10LINK
1MFR-25FBF52-1K8$0.10LINK
1CFR-12JB-52-3K3$0.10LINK
2MFR-25FBF52-100R$0.10LINK
1MFR-25FBF52-120R$0.10LINK
12N3904$0.14LINK
3WS281B$0.68LINK
1MAX485ECSA+$5.88LINK
1IO-XLR3-F-EH$2.63LINK
1IO-XLR3-M-EH$2.55LINK
1XIAO ESP-32-C3$4.99LINK
12.4Ghz Atenna$2.20LINK
1Headers$0.24LINK
Shiping$6.88
Total Excl Shiping$21.95
Total Incl Shiping$29.84

AliExpress

QTYItemPriceLink
1OLED DISPLAY$5.35LINK
Total Excl Shiping$5.35
Toatl Incl Shiping$8.34

Case

Printed With Printing Legion. Estmiated Shiping Cost Based on prevoious printing legion experiance.

QTYItemPriceLink
1Case$4.50

Tool's & Misc

QTYItemPriceLink
110g Flux$3.32 LINK
150g Solder$10.89 LINK
1M3 Heatset Inserts$2.03 LINK
1M3x14mm Screws$2.94 LINK
Total No Discount & Shiping$19.81
Total Incl Discounts & Shiping$13.36

Parts

19
QtyValueFootprintReferences
21.5KExxCADiode_THT:D_DO-201AE_P15.24mm_HorizontalD2, D3
2100ΩResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR4, R5
2MountingHole_3.2mm_M3MountingHole:MountingHole_3.2mm_M3M3, M3
11.8kΩResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR2
1120ΩResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR3
12N3904Package_TO_SOT_THT:TO-92_InlineQ1
13.3kΩResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1
1Conn_01x04KiCad-SSD1306-0.91-OLED-4pin-128x32:SSD1306-0.91-OLED-4pin-128x32J2
1DDiode_THT:D_DO-34_SOD68_P10.16mm_HorizontalD1
1DMX StatusLED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mmD4
1Light ControlLED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mmD6
1MAX485EPackage_DIP:DIP-8_W7.62mmU1
1WiFi StatusLED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mmD5
1XIAO-ESP32-C3-DIPSeeed Studio XIAO Series Library:XIAO-ESP32C3-DIPU2
1XLR3 INConnector_Audio:Jack_XLR_Neutrik_NC3MAAH_HorizontalJ1
1XLR3 OUTConnector_Audio:Jack_XLR_Neutrik_NC3FAH2_HorizontalJ3

Similar boards

  • 2 layers63 × 46 mmPi485, the printed circuit board in 3D

    Pi485

    bvarner/pi485

    An open-source TTL UART <-> RS485 converter, intended for a Raspberry Pi or Arduino

    31 parts41MIT
  • 2 layers150 × 50 mmEsp32-led smps, the printed circuit board in 3D

    Esp32-led smps

    lucysrausch/esp32-led-smps

    230V main LED smps. 2x30W Constant Current.

    179 parts30
  • 4 layers96 × 172 mmServo cpu, the printed circuit board in 3D

    Servo cpu

    wiciu15/servo2

    Servo inverter for 3-phase AC motor with/out encoder feedback

    167 parts29
  • 2 layers60 × 30 mmScoring table hardware, the printed circuit board in 3D

    Scoring table hardware

    GrappleRobotics/JMS

    Another alternative field management system for the FIRST Robotics Competition.

    30 parts18
  • 2 layers68.6 × 53.3 mmXyloShield, the printed circuit board in 3D

    XyloShield

    StefanKrupop/XyloShield

    Shield for Arduino that hosts a RFM26W radio module and allows DMX-512 connectivity

    19 parts17
  • 2 layers65 × 56.5 mmPool pi v1.1, the printed circuit board in 3D

    Pool pi v1.1

    ChaseDurand/Pool-Pi

    Hardware+software solution for controlling a Goldline/Hayward Aqualogic pool control board over WiFi via a Raspberry Pi.

    28 parts14
  • 2 layers53 × 68.7 mmEEC IV Reader, the printed circuit board in 3D

    EEC IV Reader

    flxkrmr/eec-iv-reader-arduino

    Arduino based diagnostics-tool for Fords EEC IV ECUs

    39 parts14GPL-3.0

Questions

How big is the EDMX PCB?

It measures 143 × 75.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the EDMX use?

19 parts, built around the MAX485ED. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the EDMX KiCad files?

From the Darbyshire64/EndevourDMX repository on GitHub, at the commit this page was made from: the board is Kicad/EDMX/EDMX.kicad_pcb and its schematic Kicad/EDMX/EDMX.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the EDMX design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).