Skip to the content
2 layers45.7 × 60.3 mmMiaw wifitools, the printed circuit board in 3D

This is a WiFi Tool which includes EvilTwin and Deauther, this tool is based on esp8266_deauther, this tool fully runs on esp8266

Size
45.7 × 60.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
25
Nets
17
Pads
80
Tracks, vias
328, 28
Pours
2
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
28 Nov 2023
Updated
19 Mar 2024

Overview

Miaw wifitools is an open-source printed circuit board by DX4GREY, from the DX4GREY/esp8266_wifitools repository on GitHub. It is a 2-layer board of 45.7 × 60.3 mm with 25 parts on 17 nets, routed with 328 tracks and 28 vias.

It belongs with the radio and wireless boards and the ESP8266 boards of this library.

README

WiFi Tik II/README.md

WiFiTik Prototype

This project used base firmware WiFi Tools

Component quantity

DesignatorQuantityValuePackMPNMount Type
11OLEDTHT
D1 MINI1Wemos-D1-miniwemos-d1-mini-connectors-onlyTHT
A, B, DOWN, UP4SW_PUSH_6mmSW_PUSH_6mmTHT
Hole, Hole, Hole, Hole4MountingHole_2.1mmMountingHole_2.1mmTHT
LED1LED_Cree-XQ_HandSolderingLED_Cree-XQ_HandSolderingSMT
R1, R22ResistorResistorTHT
RX, TX2Pin_D0.9mm_L10.0mm_W2.4mm_FlatForkPin_D0.9mm_L10.0mm_W2.4mm_FlatForkTHT
VIN1Power 5VPower 5VSMT

PCB Previews

Front View

Front View

Back View

Back View

About this Project

This firmware allows you to easily perform a variety of actions to test 802.11 networks using an ESP8266. It's also a great project for learning about WiFi, microcontrollers, Arduino, hacking and electronics/programming in general.

The deauthentication attack is the main feature, which can be used to disconnect devices from their WiFi network.
Although this denial-of-service attack is nothing new, a lot of devices are still vulnerable to it. Luckily this is slowly changing with more WiFi 6 enabled devices being used. But a lot of outdated WiFi devices remain in place, for example in cheap IoT hardware. With an ESP8266 Deauther, you can easily test this attack on your 2.4GHz WiFi network/devices and see whether it's successful or not. And if it is, you know you should upgrade your network.

Disclaimer

This project is a proof of concept for testing and educational purposes.
Neither the ESP8266, nor its SDK was meant or built for such purposes. Bugs can occur!

Use it only against your own networks and devices!
Please check the legal regulations in your country before using it.
We don't take any responsibility for what you do with this program.

Parts

25
QtyValueFootprintReferences
6SW_PUSH_6mmWiFiTools:SW_PUSH_6mmA, B, DOWN, GPIO 0, RESET, UP
4MountingHole_2.1mmMountingHole:MountingHole_2.1mmHOLE, HOLE, HOLE, HOLE
2LOGOWiFiTools:logoG***, G***
2Pin_D0.9mm_L10.0mm_W2.4mm_FlatForkConnector_Pin:Pin_D0.9mm_L10.0mm_W2.4mm_FlatForkRX, TX
2ResistorWiFiTools:ResistorR1, R2
1LED_Cree-XQ_HandSolderingLED_SMD:LED_Cree-XQ_HandSolderingLED
1LOGOWiFiTools:tools
1OLED_CONNECTORSWiFiTools:OLED_CONNECTORSdisplay socket
1Power 5VWiFiTools:Power 5VBattery
1SolderWirePad_1x01_SMD_1x2mmConnector_Wire:SolderWirePad_1x01_SMD_1x2mmANT 0
1Wemos-D1-miniWiFiTools:wemos-d1-mini-connectors-only(D1 MINI)
1oledWiFiTools:oled0.96 Oled SSD1306

The 23 most common of 25 parts.

More from DX4GREY/esp8266_wifitools

1
  • 2 layers30.5 × 60.3 mmMiaw wifitools, the printed circuit board in 3D

    Miaw wifitools

    DX4GREY/esp8266_wifitools

    This is a WiFi Tool which includes EvilTwin and Deauther, this tool is based on esp8266_deauther, this tool fully runs on esp8266

    20 parts19

Similar boards

  • 2 layers159.5 × 30 mmType f, the printed circuit board in 3D

    Type f

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    25 parts3kApache-2.0
  • 2 layers113.5 × 95.1 mmSweep high, the printed circuit board in 3D

    Sweep high

    davidphilipbarr/Sweep

    Sweep - a small promicro based keyboard inspired by the Ferris.

    25 parts2.1k
  • 2 layers58.4 × 114.3 mmPicoPedal, the printed circuit board in 3D

    PicoPedal

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    25 parts915
  • 2 layers54 × 15 mmXyp gpib, the printed circuit board in 3D

    Xyp gpib

    xyphro/UsbGpib

    Versatile, cheap and portable USB to GPIB converter (USBTMC class based)

    25 parts690MIT
  • 2 layers50 × 76 mmVoron 0, the printed circuit board in 3D

    Voron 0

    dennisss/dacha

    Monorepo for awesome tools/projects/libraries

    25 parts397Apache-2.0
  • 2 layers237.5 × 102.9 mmStorage, the printed circuit board in 3D

    Storage

    jes/scamp-cpu

    A homebrew 16-bit CPU with a homebrew Unix-like-ish operating system.

    25 parts301Unlicense
  • 2 layers43.3 × 21 mmNanoS3 Carrier, the printed circuit board in 3D

    NanoS3 Carrier

    UnexpectedMaker/esp32s3

    Assorted files for my ESP32-S3 development boards

    25 parts296

Questions

How big is the Miaw wifitools PCB?

It measures 45.7 × 60.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Miaw wifitools use?

25 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Miaw wifitools KiCad files?

From the DX4GREY/esp8266_wifitools repository on GitHub, at the commit this page was made from: the board is WiFi Tik II/miaw-wifitools.kicad_pcb and its schematic WiFi Tik I/miaw-wifitools.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Miaw wifitools design in my own project?

Its repository states no licence, so its author keeps all rights: ask DX4GREY before reusing the design.