Skip to the content
2 layers50.3 × 56 mmMotorControllerHeader, the printed circuit board in 3D

MotorControllerHeader

DBG-Robots/PI5-HAT-relocator

A simple, shallow KiCad board that lets the Kinematics Kit HAT fit into a narrow robot frame: female connectors on top, male connectors on bottom.

Size
50.3 × 56 mm
Copper layers
2
Thickness
1.6 mm
Parts
17
Nets
11
Pads
32
Tracks, vias
55, 417
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
30 Oct 2026
Updated
31 Oct 2026

Overview

MotorControllerHeader is an open-source printed circuit board by DBG-Robots, from the DBG-Robots/PI5-HAT-relocator repository on GitHub, published under the GPL-2.0 licence. It is a 2-layer board of 50.3 × 56 mm with 17 parts on 11 nets, routed with 55 tracks and 417 vias.

README

README.md

PI5-HAT-relocator

English Deutsch

A simple, shallow KiCad board that lets the Kinematics Kit HAT fit into a narrow robot frame: female connectors on top, male connectors on bottom.

3D render of the PI5-HAT-relocator board

Background

Our robot uses the Kinematics Kit by Eduard as its motor and drive electronics. In its canonical layout, the motor connectors stick out on the sides of the HAT. That is fine for most builds, but it costs width, and width is exactly what we do not have.

The problem

  • 30 cm width limit. This is the main constraint we are fighting. Everything, including the connectors that stick out of the kit, has to fit inside it.
  • Very shallow frame. Our double wishbone suspension (3 wheels per side) is mounted on the sides of the robot. Most other robots in the league put the suspension below the electronics enclosure, which raises the center of mass. We chose the side-mounted layout for a lower center of mass, but it leaves a much narrower and shallower space for the electronics.

The solution

This board relocates the connectors of the HAT. Rotating the top part of the Kinematics Kit HAT by 90° brings the motor connectors out of the side-protruding position, so the entire Kinematics Kit fits fully inside our frame while staying within the 30 cm width limit and the low profile we need.

The board is intentionally simple:

  • Female connectors on top and male connectors on bottom, so it sits between the Pi/HAT and the rotated top section.
  • No ribbon cable, which keeps the stack low and avoids extra bulk and wiring.
  • Silkscreen labels (VCC, GND, EN and signal pairs) on every connector to make assembly and debugging easy.

Files

FileDescription
MotorControllerHeader.kicad_pro / .kicad_sch / .kicad_pcbKiCad project, schematic and PCB layout
PI5-HAT-relocator.step3D model of the assembled board
production/Fabrication outputs (BOM, positions, netlist, zip)
SketchPi2PHeaders.dxfMechanical sketch / outline reference

Credits

Developed by DBG-Robots, Merlin Ortner (Dietrich-Bonhoeffer-Gymnasium Oberasbach). Kinematics Kit by Eduard.

Parts

17
QtyValueFootprintReferences
8Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ1, J3, J5, J7, J9, J11, J13, J15
8Conn_01x02_SocketConnector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_VerticalJ2, J4, J6, J8, J10, J12, J14, J16
1LOGOLOGOG***

Similar boards

  • 2 layers50 × 35 mmServo power, the printed circuit board in 3D

    Servo power

    earthtojake/text-to-cad

    Design physical products with AI

    17 parts26kMIT
  • 2 layers139.7 × 62.2 mmBreakout 60pin EEC IV, the printed circuit board in 3D

    Breakout 60pin EEC IV

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    17 parts1.2k
  • 2 layers29.2 × 55.9 mmDeniseadapter, the printed circuit board in 3D

    Deniseadapter

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    17 parts1kGPL-3.0
  • 2 layers24.5 × 36.5 mmCluster, the printed circuit board in 3D

    Cluster

    JesusFreke/lalboard

    A 3D-printed keyboard inspired by the DataHand

    17 parts993
  • 2 layers56.3 × 55.7 mmStarNecklace, the printed circuit board in 3D

    StarNecklace

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    17 parts915
  • 2 layers25 × 25 mmSmallEncoder, the printed circuit board in 3D

    SmallEncoder

    DDeGonge/OS-ARM

    This arm is not industrial and it will not be fast, but that is not my goal. But it will hopefully be a very nice looking arm fully capable of 6dof motion, cheap enough to keep it accessable but capable enough to…

    17 parts498MIT
  • 2 layers38.9 × 16.1 mmAmoeba spc, the printed circuit board in 3D

    Amoeba spc

    mtl/keyboard-pcbs

    Keyboard PCBs

    17 parts485
  • 2 layers36 × 51 mmABSIS ALE, the printed circuit board in 3D

    ABSIS ALE

    jrsteensen/OpenHornet

    OpenHornet 1:1 F/A-18C Simulator Repository

    17 parts431

Questions

How big is the MotorControllerHeader PCB?

It measures 50.3 × 56 mm and has 2 copper layers, 1.6 mm thick.

What parts does the MotorControllerHeader use?

17 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the MotorControllerHeader KiCad files?

From the DBG-Robots/PI5-HAT-relocator repository on GitHub, at the commit this page was made from: the board is MotorControllerHeader.kicad_pcb and its schematic MotorControllerHeader.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the MotorControllerHeader design in my own project?

Its repository publishes it under the GPL-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).