

Fixture friend
Cheap quickstart platform for bed-of-nails test fixtures, based on RP2040 MCU
- Size
- 100 × 100 mm
- Copper layers
- 2
- Thickness
- 1 mm
- Parts
- 42
- Nets
- 67
- Pads
- 214
- Tracks, vias
- 286, 34
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 26 Oct 2026
- Updated
- 26 Oct 2026
Overview
Fixture friend is an open-source printed circuit board by Cushychicken, from the Cushychicken/fixture-friend repository on GitHub. It is a 2-layer board of 100 × 100 mm with 42 parts on 67 nets, routed with 286 tracks and 34 vias.
It is built around the RP2040, W25Q128JVSIQ and SM04B-SRSS-TB(LF)(SN), with the SM06B-SRSS-TB(LF)(SN) and TSW-102-07-G-S among its other parts. Its parts include 17 capacitors, 9 resistors, 8 connectors, 3 ICs and 1 crystal. It belongs with the RP2040 boards of this library.
Main components
5RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHSM04B-SRSS-TB(LF)(SN)
SMD,P=1mm,卧贴-25℃~+85℃ 1 1A 1mm 1x4P 2.9mm 4 4.32mm 4P 50V 6mm Auxiliary Solder Pin Copper alloy PA SH Surface Mount, Right Angle Tin UL94V-0 White SMD,P=1mm,卧贴 Wire To Board Connector ROHSJSTWire To Board ConnectorSM06B-SRSS-TB(LF)(SN)
SMD,P=1mm,卧贴-25℃~+85℃ 1 1A 1mm 1x6P 2.9mm 4.32mm 50V 6 6P 8mm Auxiliary Solder Pin Copper alloy PA SH Surface Mount, Right Angle Tin UL94V-0 White SMD,P=1mm,Surface Mount,Right Angle Wire To Board Connector ROHSJSTWire To Board ConnectorTSW-102-07-G-S
插件,P=2.54mm-55℃~+125℃ 1 1x2P 2.54mm 2.54mm 2.54mm 2P 5.84mm Black Gold Phosphor bronze Pin Header Through Hole 插件,P=2.54mm Pin Headers ROHSSamtecPin Headers
README
README.mdfixture-friend
A Kicad 10 design block and board implementation to help make bed-of-nails programming fixtures quickly. Intentionally implemented in this as two layers, so it's cheap and quick to produce assembled at JLCPCB.
Features:
- 100mm x 100mm board outline
- M3 mounting holes in each corner
- Core RP2040 design as hierarchical sheet
- Connections to target PCBA and target programming connectors implemented
Design block is fanned out to a few common connector specs, for easy implementation as a reference design:
- SWD: Samtec FTSH 10 pin (standard ARM)
- UART: Molex PicoBlade 4-pin debug connector (keyed differently from QWIIC)
- I2C: QWIIC connector
- SPI: JST-SH 6-pin debug connector
Also included: USB-C to pogo pin interface, to easily land on a set of pogo pins.
- Note: not tested with USB 2.0 high speed links. Only USB 1.1 operation is assured.
RP2040 debug interfaces
The dedicated debug connectors are on the root schematic and are exported from the
ff-core hierarchical sheet. They use unassigned RP2040 GPIOs and the following
alternate functions:
| Interface | Connector | Pin order | RP2040 GPIO | RP2040 function |
|---|---|---|---|---|
| UART | J8, Molex PicoBlade 53261-0471 | 1 GND, 2 VTREF (+3V3), 3 TX, 4 RX | GPIO4, GPIO5 | UART1 TX (probe to target RX), UART1 RX (target TX to probe) |
| SPI | J9, JST SM06B-SRSS-TB(LF)(SN) | 1 GND, 2 VTREF (+3V3), 3 SCLK, 4 MOSI, 5 MISO, 6 CS_N | GPIO10, GPIO11, GPIO8, GPIO9 | SPI1 SCK, TX, RX, CSn |
J8 uses the KiCad Connector_Molex right-angle, 1.25 mm pitch PicoBlade footprint;
its incompatible keying prevents a QWIIC cable from being plugged into UART. J9 uses
the KiCad Connector_JST right-angle, 1.00 mm pitch JST-SH footprint. Both are
grouped along accessible board edges. VTREF is a 3.3 V reference output; it is not
intended as an external power input.
The on-board RP2040 is intended to run Raspberry Pi Debug Probe firmware. Its target SWD engine is GPIO12 (SWCLK drive), GPIO13 (SWD sample input), and GPIO14 (SWD drive); GPIO4/GPIO5 are the firmware's UART1 TX/RX pins. This implementation is intentionally limited to 3.3 V targets, so GPIO13 and GPIO14 share the target SWDIO net directly. The RP2040 package pins named SWCLK and SWDIO are reserved for programming this probe itself and are not the target-programmer outputs.
Parts
42| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100n | RPI_COMPILED:generic_capc1005x50 | C5, C6, C7, C9, C11, C12, C13, C14, C15, C16 |
| 4 | 5.1k | Resistor_SMD:R_0603_1608Metric | R20, R21, R23, R24 |
| 4 | NPTH FD2.75mm SM3.15mm KO6mm | RPI_COMPILED:none_mh_npth_fd2p75mm_sm3p15mm_ko6mm | MH1, MH2, MH3, MH4 |
| 3 | 10u | RPI_COMPILED:generic_capc2012x125 | C1, C4, C17 |
| 2 | 15p | RPI_COMPILED:generic_capc1005x50 | C2, C3 |
| 2 | 1k | RPI_COMPILED:generic_resc1005x35 | R1, R5 |
| 2 | 1u | RPI_COMPILED:generic_capc1005x50 | C8, C10 |
| 2 | 27 | RPI_COMPILED:generic_resc1005x35 | R3, R4 |
| 2 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4085 | J3, J7 |
| 1 | 10k | RPI_COMPILED:generic_resc1005x35 | R2 |
| 1 | 12MHz | RPI_COMPILED:generic_xtalcc320x250x80-4 | X1 |
| 1 | 53261-0471 | Connector_Molex:Molex_PicoBlade_53261-0471_1x04-1MP_P1.25mm_Horizontal | J8 |
| 1 | Conn_02x02_Odd_Even | Harwin_P70-2200045:Harwin_P70-2200045_2x02_P2.54mm | J5 |
| 1 | Conn_ARM_JTAG_SWD_10 | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMD | J1 |
| 1 | NCP1117ST33T3G | RPI_COMPILED:onsemi_ncp1117st33t3g | U1 |
| 1 | RP2040 | RPI_COMPILED:rpi_rp2040_vias | U3 |
| 1 | SM04B-SRSS-TB(LF)(SN) | Connector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J6 |
| 1 | SM06B-SRSS-TB(LF)(SN) | Connector_JST:JST_SH_SM06B-SRSS-TB_1x06-1MP_P1.00mm_Horizontal | J9 |
| 1 | TSW-102-07-G-S | RPI_COMPILED:samtec_tsw-102-07-g-s | J2 |
| 1 | W25Q128JVSIQ | RPI_COMPILED:generic_soic127p790x195-8 | U2 |
Similar boards
- 2 layers42 × 50 mm

- 6 layers40 × 40 mm

Kestrel fc
HeyPCB/kestrel-fc
Kestrel H7: STM32H743 FPV flight controller with ICM-20602 + BMI088, MS5611, 16 MB blackbox, 5 V and switchable 10 V BECs.
114 partsCERN-OHL-S-2.0 - 4 layers63.7 × 41.1 mm

KiCad Advanced Design a smart USB thumb drive
gorkemguven/RP2040-Dual-TypeC-eMMC-Board
A 4-layer embedded development board featuring RP2040, USB2244 high-speed eMMC bridge, dual Type-C ports, and INA226/TMP119 power & telemetry monitoring.
133 partsMIT - 2 layers52 × 51 mm

RPI RP2040-MINIMAL R3-S1
JesseLevine727/AirNote
A touchless musical instrument built around a fully integrated RP2040, VL53L1X distance sensor and MAX98357A speaker amplifier. One hand selects eleven pentatonic notes over two octaves.
34 parts - 2 layers55 × 95 mm

- 6 layers111 × 111 mm

Led panel
antmicro/programmable-led-panel
LED matrix controlled with iCE40 FPGA or RP2040 MCU for benchmarking and integration of video systems
315 parts2Apache-2.0 - 4 layers80 × 40 mm

Audio latency tester board
antmicro/audio-latency-tester-board
This project contains open hardware design files for an audio latency processing board. The system allows driving an external speaker and collecting audio samples from a pair of PDM or I2S microphones.
240 parts1Apache-2.0 - 4 layers58 × 50 mm

Bldc motor cntroller
azmat-bilal/bldc_motor_controller_pcb
A Brushless DC Motor controller board. The design is inspired and is compatible with Odrive project (https://github.com/madcowswe/ODriveHardware) except that this one has a single channel.
146 parts112MIT
Questions
How big is the Fixture friend PCB?
It measures 100 × 100 mm and has 2 copper layers, 1 mm thick.
What parts does the Fixture friend use?
42 parts, built around the RP2040, W25Q128JVSIQ, SM04B-SRSS-TB(LF)(SN) and SM06B-SRSS-TB(LF)(SN). The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Fixture friend KiCad files?
From the Cushychicken/fixture-friend repository on GitHub, at the commit this page was made from: the board is fixture-friend/fixture-friend.kicad_pcb and its schematic fixture-friend/ff-core.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Fixture friend design in my own project?
Its repository states no licence, so its author keeps all rights: ask Cushychicken before reusing the design.