
Racer
StuckAtPrototype/Racer
These are structured into their own files. I could have used submodules, but decided against it.

PMIC PCB designed by shaurya gupta
Shaurya AGV Embedded PCB nPM110- is an open-source printed circuit board by Coder0407, from the Coder0407/Shaurya-AGV-Embedded-PCB-nPM110- repository on GitHub. It is a 2-layer board of 35 × 35 mm with 24 parts on 24 nets, routed with 198 tracks and 119 vias.
It is built around the BSS138. Its parts include 5 capacitors, 5 resistors, 3 diodes, 2 transistors and 1 IC.
This project involves the design and layout of a high-efficiency Power Management Module based on the Nordic nPM1100 PMIC. The board is engineered to provide a robust 3V logic rail at a nominal 200ma charging rate. The PCB follows a 2-Layer approach where Copper Pour(Ground) has been done on both planes with a primary focus on maintaining a solid, contiguous Ground Plane on the bottom layer. By minimizing signal routing on the bottom a low-impedance return path for the high-frequency switching currents is ensured The Designs prioritises Power integrety , a effort has been made into ensuring minimum SW- trace and keeping the decoupling capacitors as close as possible with multiple ground vias attached to them Various LED for power CHG and ERR are placed , MCU is exposed to multiple pins including CHG ERR Mode SHPACT and a battery charge monitering system has been introduced. A switch has also been connected to SHPLD to turn on the IC manually. Values of various Pins like VSET and resistance like R_ICHG are tune to ensure a 200ma nominal charging current and a max 4.2VBAT with the data from the datasheet. In the battery monitering system the MCU is given controll through Q1 and Q2 on when to measure the battery voltage, to reduce power loss .
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 10uF_10V_X5R | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C4, C5 |
| 3 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1, D2, D3 |
| 2 | BSS138 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 1 | 100K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6 |
| 1 | 10uF_6.3V_X5R | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3 |
| 1 | 10u_10V_X5R | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R_ICHG2 |
| 1 | 1K5 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R_ICHG1 |
| 1 | 1M0 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2 |
| 1 | 1M5 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
| 1 | 220K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4 |
| 1 | 2R2uH | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L1 |
| 1 | 4R2V | Connector_JST:JST_PH_B2B-PH-SM4-TB_1x02-1MP_P2.00mm_Vertical | Battery1 |
| 1 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical_SMD_Pin1Left | J1 |
| 1 | Conn_01x08_Pin | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical_SMD_Pin1Left | MCU_HEADER1 |
| 1 | R | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5 |
| 1 | SW_Push | Button_Switch_SMD:SW_Push_1P1T_NO_CK_KMR2 | SW2 |
| 1 | Thermistor_NTC | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | TH1 |
| 1 | VALUE | Package_DFN_QFN:HVQFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm_ThermalVias | U1 |

StuckAtPrototype/Racer
These are structured into their own files. I could have used submodules, but decided against it.

willem-pennings/balancing-cube
A cube that balances itself in a corner or edge using reaction wheels

abhishek-kakkar/BeagleLogic
A Software Suite that implements a logic analyzer with the PRU on the BeagleBone / BeagleBone Black.


lachlanA/eagle-to-kicad
Eagle SCH/LIB to KiCad SCH/LIB ULP conversion script

No0ne/ps2x2pico
USB keyboard/mouse to PS/2 interface converter using a Raspberry Pi Pico

StuckAtPrototype/AirCube
Works standalone out of the box. Pairs with Home Assistant in minutes. Other platforms are supported through community-contributed extensions.

It measures 35 × 35 mm and has 2 copper layers, 1.6 mm thick.
24 parts, built around the BSS138. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Coder0407/Shaurya-AGV-Embedded-PCB-nPM110- repository on GitHub, at the commit this page was made from: the board is Board.kicad_pcb and its schematic Schematic.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Coder0407 before reusing the design.