
PIC32MX130 SpeakingClock20170701
ClockWorks001/PIC32MX130_SpeakingClock_20170212
This is a Speaking Clock project with [PIC32MX130 micro controller][2] with [MPLAB.X][3] [MCC][4]. I have created this project using Mr.ChaN's wonderful FatFs program.

This is a Speaking Clock project with [PIC32MX130 micro controller][2] with [MPLAB.X][3] [MCC][4]. I have created this project using Mr.ChaN's wonderful FatFs program.
PIC32MX130 SpeakingClock20170301 is an open-source printed circuit board by ClockWorks001, from the ClockWorks001/PIC32MX130_SpeakingClock_20170212 repository on GitHub. It is a 2-layer board of 70 × 70 mm with 64 parts on 37 nets, routed with 469 tracks and 17 vias.
It is built around the PIC32MX130F064B-I/ML. Its parts include 13 capacitors, 13 resistors, 4 connectors, 4 switches and 3 ICs. It belongs with the PIC boards of this library.
This is a Speaking Clock project with PIC32MX130 micro controller with MPLAB.X MCC. I have created this project using Mr.ChaN's wonderful FatFs program. You can operat it by terminal with serial communication speed of 115,200 bps.
References. http://elm-chan.org/fsw/ff/00index_e.html http://microchip.wikidot.com/swtools:start
I created this project using the free versions of the following tools:
You shoud download and install these tools appropriately before you will open this project and build it. I use the Microchip MPLAB PICkit3 In-Circuit Debugger to program the chip and debug it.
Also, I use the KiCad to draw the electric circuit schematic.
Hiroshi Murakami
https://github.com/ClockWorks001
| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 10K | lib:R4_MU | R5, R6, R7, R8, R9, R11, R12, R13 |
| 4 | 1uF | lib:C2_MU | C8, C9, C10, C11 |
| 4 | PAD | lib:PAD3mmX5mm | PAD15, PAD16, PAD17, PAD18 |
| 4 | SW_PUSH | lib:SW_PUSH-12mm+_AK | SW1, SW2, SW3, SW4 |
| 3 | 0.1uF | lib:C2_MU | C3, C4, C5 |
| 2 | 100K | lib:R4_MU | R2, R3 |
| 2 | 10uF | lib:C2_MU | C6, C7 |
| 2 | 33pF | lib:C2_MU | C1, C2 |
| 2 | GND | lib:PAD1mmX1.5mmX2.5mm | PAD13, PAD14 |
| 1 | 10-20K/1M | lib:CDS_5mm | CDS1 |
| 1 | 100 | lib:R4_MU | R4 |
| 1 | 10K | lib:TERMINAL_3P | RVR1 |
| 1 | 10uF | lib:CP2_MU | C12 |
| 1 | 1F | lib:C_SE-5R5 | CP1 |
| 1 | 1K | lib:R4_MU | R10 |
| 1 | 1S3 | lib:D4_MU | D1 |
| 1 | 1nF | lib:C2_MU | C13 |
| 1 | 220 | lib:R4_MU | R1 |
| 1 | 32.768Khz | lib:X_TAL_VT200 | Y1 |
| 1 | AE-MICRO-SD-DIP | lib:SD_CARD_AE-MICRO-SD-DIP | SDC1 |
| 1 | AN0_CDS_P2 | lib:PAD1mmX1.5mmX2.5mm | PAD1 |
| 1 | CN-ICSP | lib:PINHEAD1-6_MU | CN2 |
| 1 | CN-POWER | lib:TERMINAL_2P | CN1 |
| 1 | CN-UART-FTDI-TTL-232R-3V3 | lib:PINHEAD1-6_MU | CN3 |
| 1 | HT82V739 | lib:DIP-8_300_MU | U4 |
| 1 | LCD_I2C_AQM1602XA-RN-GBW | lib:PINHEAD1-5_MU2 | CN4 |
| 1 | LED | lib:LED-5MM_AK | D2 |
| 1 | LP2950L | lib:TO92 | U1 |
| 1 | PIC32MX130F064B | lib:DIP-28_300_MU | U3 |
| 1 | PWM_P16 | lib:PAD1mmX1.5mmX2.5mm | PAD9 |
| 1 | RA1_SPI_SDO2_P3 | lib:PAD1mmX1.5mmX2.5mm | PAD2 |
| 1 | RA2_SW_P9 | lib:PAD1mmX1.5mmX2.5mm | PAD5 |
| 1 | RA3_SW_P10 | lib:PAD1mmX1.5mmX2.5mm | PAD6 |
| 1 | RB14_P25 | lib:PAD1mmX1.5mmX2.5mm | PAD11 |
| 1 | RB2_SW_P6 | lib:PAD1mmX1.5mmX2.5mm | PAD3 |
| 1 | RB3/AN5_SW_P7 | lib:PAD1mmX1.5mmX2.5mm | PAD4 |
| 1 | RB5_POWER_P14 | lib:PAD1mmX1.5mmX2.5mm | PAD7 |
| 1 | RB6_LED_P15 | lib:PAD1mmX1.5mmX2.5mm | PAD8 |
| 1 | SPEAKER | lib:TERMINAL_2P | SP1 |
| 1 | SPI_SCK2_P26 | lib:PAD1mmX1.5mmX2.5mm | PAD12 |
| 1 | SPI_SDI2_P24 | lib:PAD1mmX1.5mmX2.5mm | PAD10 |
| 1 | SW_RESET | lib:SW_PUSH-6mm_AK | SW_RESET1 |

ClockWorks001/PIC32MX130_SpeakingClock_20170212
This is a Speaking Clock project with [PIC32MX130 micro controller][2] with [MPLAB.X][3] [MCC][4]. I have created this project using Mr.ChaN's wonderful FatFs program.

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

drandyhaas/KiCadRoutingTools
A set of Python/Rust tools to aid routing in KiCad

BlueSCSI/BlueSCSI-v2
BlueSCSI v2/Ultra - an open source, open hardware, SCSI emulator using the Pi Pico PR2040 and Pico 2 RP2350



PyrooL/Alpha
A 28-key semi-ortholinear mechanical keyboard designed by PyroL

ugcs/ddc
Drone Show Software is software designed for drone shows, allowing flight path planning as well as control of dozens of drones simultaneously in a synchronized manner.

It measures 70 × 70 mm and has 2 copper layers, 1.6 mm thick.
64 parts, built around the PIC32MX130F064B-I/ML. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ClockWorks001/PIC32MX130_SpeakingClock_20170212 repository on GitHub, at the commit this page was made from: the board is KICAD/PIC32MX130_SpeakingClock20170301.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask ClockWorks001 before reusing the design.