Skip to the content
2 layers54 × 86.7 mmTempomat v1, the printed circuit board in 3D

It's bare metal and I started writing it with HW v1, so I have to make some changes.

Size
54 × 86.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
74
Nets
60
Pads
253
Tracks, vias
350, 125
Pours
9
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
4 Sep 2024
Updated
5 Feb 2025

Overview

Tempomat v1 is an open-source printed circuit board by CezWAT, from the CezWAT/universal-cruise-control repository on GitHub. It is a 2-layer board of 54 × 86.7 mm with 74 parts on 60 nets, routed with 350 tracks and 125 vias.

It is built around the 1N4148W, AOD423 and BC847, with the RFD14N05LSM among its other parts. Its parts include 18 capacitors, 16 resistors, 10 diodes, 8 connectors and 6 transistors. It belongs with the STM32 boards of this library.

Main components

4

README

README.md

Universal cruise control for cars

What it is

This project is about to bring cruise control to my Fiat 126p, but basically it should be possible to adapt it to any car.

Sensors used

  • hall sensor as a speed sensor
  • brake light switch (already in place)
  • clutch switch (has to be added)
  • Three buttons (+, -, cancel)

What is driving what

Based on the speed sensor, the device regulates PWM signal with PI loop. It tries to keep the vehicle speed as close as possible to the one set with the buttons. What controls the engine is a simple, but "strong" servomotor. In my case it is TiankongRC TD-6620MG (they say it has metal gears, 180 degrees of movement and 20 kg of torque). The servo is attached to gas pedal linkage as it is a simple connection and there are no vibrations on the floor compared to the engine.

Where is the firmware

In FW directory. Be aware, that for now it is only a proof of concept made for HW v. 1. There are many functions that I would like to work but I didn't code it yet.

It's bare metal and I started writing it with HW v1, so I have to make some changes.

Changes in HW between versions

v1:

  • controls DC motor with H bridge. It came out as not so simple due to lack of motor position sensing.
  • buttons and switches had to be debounced in code, this takes time and control over cruise control is somehow critical on the road.
  • buttons were driven from the VCC.
  • I misplaced pins in AMSR20783.3JZ footprint.

v2:

  • improved misconceptions from above.
  • JST connectors instead of goldpins.
  • improved routing and footprints (for example SOT123 in place of SOT323 for improved solderability).

Parts

74
QtyValueFootprintReferences
1210kResistor_SMD:R_0603_1608MetricR2, R3, R4, R5, R7, R9, R10, R11, R12, R13, R14, R15
10100nCapacitor_SMD:C_0603_1608MetricC1, C2, C5, C6, C13, C14, C15, C16, C17, C18
5D_TVSDiode_SMD:D_SOD-323_HandSolderingD6, D7, D8, D9, D10
5SW_PushButton_Switch_THT:SW_PUSH_6mmSW1, SW2, SW3, SW4, SW5
41N4148WDiode_SMD:D_SOD-123D1, D2, D4, D5
210u/25VCapacitor_SMD:C_1206_3216MetricC8, C9
21kResistor_SMD:R_0603_1608MetricR1, R6
222pCapacitor_SMD:C_0603_1608MetricC3, C4
2AOD423Package_TO_SOT_SMD:TO-252-3_TabPin1Q2, Q4
2BC847Package_TO_SOT_SMD:SOT-23Q1, Q6
2Conn_01x02Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ6, J7
2Conn_01x03Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ5, J8
2Conn_01x04Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ3, J4
2MountingHoleMountingHole:MountingHole_3.5mmH1, H2
2RFD14N05LSMPackage_TO_SOT_SMD:TO-252-3_TabPin1Q3, Q5
2VAL**Library:mouse-bite-3mm-slotmouse-bite-3mm-slot, mouse-bite-3mm-slot
1100kResistor_SMD:R_0603_1608MetricR8
1100nCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC11
1100uInductor_SMD:L_1210_3225Metric_Pad1.42x2.65mm_HandSolderL2
1100u/25VCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC7
1120Resistor_SMD:R_0603_1608MetricR16
122u/25VCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC12
1680u/25VCapacitor_THT:CP_Radial_D10.0mm_P5.00mmC10
18MHzCrystal:Crystal_SMD_EuroQuartz_MJ-4Pin_5.0x3.2mmY1
1>2AFuse:Fuse_0805_2012MetricF1
1AMSR2-783.3JZ AIMTECtmp:AMSR2-78JZU2
1Conn_01x02TerminalBlock:TerminalBlock_bornier-2_P5.08mmJ1
1Conn_01x07Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_VerticalJ2
1Motor_DCConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalM1
1REDDiode_SMD:D_0603_1608MetricD3
1RL622-220K-RC BOURNSInductor_THT:L_Radial_D8.7mm_P5.00mm_Fastron_07HCPL1
1STM32F103C8TxPackage_QFP:LQFP-48_7x7mm_P0.5mmU1

More from CezWAT/universal-cruise-control

1
  • 2 layers54 × 86.7 mmTempomat v2, the printed circuit board in 3D

    Tempomat v2

    CezWAT/universal-cruise-control

    It's bare metal and I started writing it with HW v1, so I have to make some changes.

    67 parts

Similar boards

  • 2 layers101.6 × 147.3 mmKarabas pro revER, the printed circuit board in 3D

    Karabas pro revER

    andykarpov/karabas-pro

    FPGA based retrocomputer with FDD and HDD controllers

    223 parts37MIT
  • 4 layers71.5 × 71.5 mmElixir, the printed circuit board in 3D

    Elixir

    golioth/elixir-hw

    An open source hardware device that has cellular, wifi, bluetooth, GPS, and more!

    249 parts36CERN-OHL-P-2.0
  • 2 layers100 × 100 mmZxevo1010 main, the printed circuit board in 3D

    Zxevo1010 main

    UzixLS/zxevo1010-board

    10x10cm PCB variant of ZX-Evolution project for G738/G706 enclosure

    252 parts26
  • 2 layers39.6 × 100 mmSteinerVCF, the printed circuit board in 3D

    SteinerVCF

    marangisto/SteinerVCF

    Steiner VCF Replica

    72 parts5MIT
  • 4 layers101.6 × 147.3 mmKarabas go, the printed circuit board in 3D

    Karabas go

    andykarpov/karabas-go-pcb

    Karabas-Go PCB

    311 parts3
  • 2 layers49.4 × 43.7 mmChaos papagali, the printed circuit board in 3D

    Chaos papagali

    Pakequis/Chaos_papagali

    A annoying device that imitates the vibration of a phone

    41 parts2MIT
  • 2 layers120.1 × 46 mmGeiger EDW, the printed circuit board in 3D

    Geiger EDW

    Sidolux/geiger_counter

    Geiger Counter (STS-5) designed with KiCad

    60 parts1
  • 4 layers81 × 113.2 mmAuralab Workstation Vishal, the printed circuit board in 3D

    Auralab Workstation Vishal

    Vishalbabu-09/Auralab_Workstation

    Advanced 4-layer PCB design featuring split-plane noise isolation (AGND/DGND) and asynchronous dual-core processing. Implements a handheld multi-tool oscilloscope, current tracker, and symmetrical DC power supply.

    81 parts1

Questions

How big is the Tempomat v1 PCB?

It measures 54 × 86.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Tempomat v1 use?

74 parts, built around the 1N4148W, AOD423, BC847 and RFD14N05LSM. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Tempomat v1 KiCad files?

From the CezWAT/universal-cruise-control repository on GitHub, at the commit this page was made from: the board is HW/v1/tempomat_v1/tempomat_v1.kicad_pcb and its schematic HW/v1/tempomat_v1/tempomat_v1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Tempomat v1 design in my own project?

Its repository states no licence, so its author keeps all rights: ask CezWAT before reusing the design.