Skip to the content
4 layers188.9 × 92 mmMegaCD, the printed circuit board in 3D

Reproductions of main board PCBs for Sega's Mega CD/Sega CD add-on for the Mega Drive/Genesis console.

Size
188.9 × 92 mm
Copper layers
4
Thickness
1.6 mm
Parts
132
Nets
347
Pads
1,138
Tracks, vias
7,524, 826
Pours
114
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
3 Jul 2023
Updated
3 Oct 2025

Overview

MegaCD is an open-source printed circuit board by Board-Folk, from the Board-Folk/MegaCD-Main-BD repository on GitHub. It is a 4-layer board of 188.9 × 92 mm with 132 parts on 347 nets, routed with 7,524 tracks and 826 vias.

It is built around the 74HC245D, 74AC74M and 74HC86D, with the CL10B474KA8NNN among its other parts. Its parts include 58 capacitors, 17 ICs, 12 resistors and 3 connectors. It belongs with the retro computing and games boards of this library.

Main components

4

README

README.md

Sega Mega CD Main BD Reproductions

This repository contains recreations of main board PCBs for Sega's Mega CD/Sega CD add-on for the Mega Drive/Genesis console. These boards are often subject to damage caused by leaking capacitors and/or batteries. The recreations are based on the available schematics and reverse engineering using scanned images of the original boards' copper layers, so should be reasonably accurate reproductions.

NOTE: In order to use these PCBs sucessfully you will need to be proficient in:

  • Soldering fine-pitched surface mount components.
  • In most cases, desoldering said components to obtain these from a donor board.
  • Troubleshooting any issues that may arise.

The authors are not obliged to provide support, nor shall they be held responsible for botched attempts at using these boards.

Should you however find a legitimate flaw in the board's design or have suggestions for improvements, please feel free to submit an issue. Please note that the current scope of the project is to provide a working replica; we are not at this moment entertaining feature requests for significant modifications.

Revisions

Current research suggests that there were 3 PCB part numbers for the main board. One of these was used with two different MCE chips (the large 208-pin custom chip) resulting in four known revisions. Aside from the markings on the board, the revisions are easily identified using the table below. Obviously, be sure to select the correct replacement board for your purposes.

BoardProgram RAMMCE ChipMCE LogicRegionPCM ChipPCM Logic
837-8015Zip315-5477 (MCE1)JK-FF (IC19)Japan315-5476None
837-8015-01Zip315-5548 (MCE2)D-FF (IC19)Japan315-5476AXOR (IC16)
837-8952SOJ315-5548 (MCE2)D-FF (IC17)Export315-5476AXOR (IC12)
837-8952SOJ315-5632 (MCE3)None (IC17)Export315-5476AXOR (IC12)

Of these revisions, only the schematics for 837-8015-01 are easy to find online. Luckily there are only a few minor differences between the revisions, all of which are now documented in the schematics of this project.

Different revisions of the MCE require different support logic chips. On the 837-8015 this is partially implemented in the "tree house" daughter board (on which the oscillator is mounted) and the "connect board" which connects to the console (see this project if you require a replacement). Later versions have no daughter board and have connect boards with only passive components. Note that if you are mixing and matching parts, there are also variations of the passive connect board with and without particular capacitors, etc. installed. An incorrect combination will usually manifest itself as graphical glitches on the BIOS "intro" screen.

For the 837-8952 be doubly sure to check which MCE revision is used and therefore whether IC17 should be populated or not.

Rumour has it that the MCE3 chip (315-5632) can be used on the 837-8015 board if you also use the passive style connect board. We have not yet confirmed this to be the case but it is plausible judging by the schematics.

If you have a revision or combination not listed above, we'd be interested to hear about it.

PCB Production

Minimum track widths, clearances and via sizes are within the standard offering of modern PCB fabricators. Development was done using JLCPCB and the boards therefore have their order number placeholder on the silkscreen, which you may wish to remove if using another service.

We recommend using at least 4 layers for all boards. For optimal EMI performance you may opt to use 6 layers by replicating the internal ground and power planes (e.g. top, ground, power, power, ground, bottom) but this is likely to be significantly more expensive.

  • 837-8015: the original boards were produced using a process that added a partial layer of copper on top of the signal layers, separated by some sort of dielectric coating. During testing, 2-layer boards without this copper layer suffered from noise issues so these have now been updated with internal power and ground planes. Despite these additions, this particular board can still present challenges even to seasoned builders.

  • 837-8015-01: this revision has improved routing and 2-layer boards have been shown to work. The design does however have 4 layers and we recommend using these.

  • 837-8952: the original "Export" board was 4 layers so this is also the only option due to reliance on internal ground and power planes.

Bill of Materials

Most parts are marked on the board and it is expected that these will be reused from a donor board. It is completely possible that your particular board uses different (but compatible) parts so it's advisable to take photos before starting. The zip RAM is not marked on the PCB but their position is obvious from the number of pins. Take care to mount the SMD RAM in the correct positions as some parts have very similar part numbers.

Below is therefore a partial bill of materials for parts whose values are not marked on the boards and/or look otherwise alike. For the 837-8952 "Export" boards, almost all references were renumbered so be sure to use the correct column on the left to identify the parts. I would seriously recommend printing the list and covering/removing/otherwise obscuring the irrelevant column to avoid confusion.

Values for the capacitors unique to the 837-8952 "Export" board are based on measurements of components on an original example and therefore potentially inaccurate. The values are however also likely not very critical, e.g. 100pF will probably be fine (maybe even closer to the original specification) where 133pF is stated. If in doubt, you may like to reuse the components from your donor board.

Capacitor voltages may exceed those given, within reason. E.g. you may substitute 10V for a 6.3V part. Do not, however, use a lower voltage than specified. No voltage is specified for the ceramic capacitors; any 0805 part is expected to exceed the required voltage anyway. For SMD electrolytics a diameter of 3-4mm is specified. The originals are about 3mm but you can just about get away with 4.3mm.

The right-most columns indicate whether (and where) the part is populated on that revision. T = Top of board, B = bottom of board and a "-" = unpopulated. As a rule THT and electrolytic capacitors are on top, ceramic capacitors and resistors on the bottom. The exception is the two LEDs (L1 and L2) which mount, bent at right angles, to the bottom of the board. For best results, mount these facing outwards, towards the front of the machine.

Reference (Japan)Reference (Export)ValueVoltageFootprint837-8015837-8015-01837-8952
C1C11uF0805BBB
C2C222nF0805BBB
C3C322nF0805BBB
C4C622nF0805BBB
C5C522nF0805BBB
C6-22nF0805BB-
C7-22nF0805BB-
C8-22nF0805BB-
C9C4110uF16VSMD 3-4mmTTT
C10-10uF16VSMD 3-4mmTT-
C11C4210uF16VSMD 3-4mmTTT
C12-10uF16VSMD 3-4mmTT-
C13-10uF16VSMD 3-4mmTT-
C14C422nF0805BBB
C15C32n/u-----
C16C22n/u-----
C17-n/u-----
C18-n/u-----
C19-n/u-----
C20-n/u-----
C21-n/u-----
C22-n/u-----
C23C4310uF16VSMD 3-4mmTTT
C24C722nF0805BBB
C25C1122nF0805BBB
C26C51100uF6.3VTHT 5mm pitchTTT
C27C922nF0805BBB
C28C4510uF16VSMD 3-4mmTTT
C29C23100pF0805BB-
C30C1022nF0805BBB
C31C4610uF16VSMD 3-4mmTTT
C32C26100pF0805BB-
C33C27100pF0805--B
C34C28100pF0805BBB
C35C24100pF0805--B
C36C25100pF0805BBB
C37C4710uF16VSMD 3-4mmTTT
C38C1322nF0805BBB
C39C1422nF0805BBB
C40C1522nF0805BBB
C41C4810uF16VSMD 3-4mmTTT
C42C4910uF16VSMD 3-4mmTTT
C43C1622nF0805BBB
C44C1822nF0805BBB
C45C1722nF0805BBB
C46C5010uF16VSMD 3-4mmTTT
C47C36200pF0805-B-
C48C52100uF6.3VTHT 5mm pitchTTT
C49C1922nF0805BBB
C50C2022nF0805BBB
C51C1222nF0805BBB
C52C822uF0805-BB
C53C4410uF16VSMD 3-4mm-TT
C54C21100pF0805--B
C55C3333pF0805--B
C56C3482pF0805--B
C57C30n/u0805---
C58C53n/u0805---
-C2950pF0805--B
-C31133pF0805--B
-C3560pF0805--B
-C37200pF0805--B
-C38133pF0805--B
-C39100pF0805--B
-C40200pF0805--B
-C54n/u0805---
-C55n/u0805---
-C56n/u0805---
-C57n/u0805---
-C58n/u0805---
CX1-51pFTHT axial*B--
R1R14.7K0805BBB
R2R24.7K0805BBB
R3R52.2K0805BBB
R4R73600805BBB
R5R61600805BBB
R6R34.7K0805BBB
R7R44.7K0805BBB
-R8-1200805--See note**

* CX1 (to give it a name) was mounted on the bottom of 837-8015 boards from the factory, between pins 2 and 38 of IC4. You may like to replicate this the same way, or you may use the extra 0805 footprint provided for this purpose. You may even want to live dangerously and leave it off.

** These 0-ohm resistors are used to configure the board depending on the MCE revision, etc.:

  • R8 and R9: these have the pads shorted on the board so no resistor need be fitted.
  • R10: Fitted only for MCE3, in which case IC17 is unpopulated.
  • R11 and R12: these affect how /CLWE is passed to the PCM chip. With R11 installed, this is passed directly like on the 837-8015 board with the 315-5476 (no "A" suffix) PCM chip. With R12 installed the signal is passed through an XOR gate like on the 837-8015-01 board with the 315-5476A (with "A" suffix) installed. This may be useful if you are mixing and matching parts from different boards but the best course of action is to note which of these resistors/jumpers is installed on the original board you are replacing. In any case, DO NOT install both R11 and R12 as this will likely damage IC12.

Modifications

Whilst the PCB layouts are meant to be close replicas of the original, some minor practical modifications have been made.

837-8015 (Japanese "Rev 0")

This revision came from the factory with a capacitor installed directly to the underside of IC4 (the ROM). For your convenience a dedicated SMD footprint has been added so this can be mounted more neatly.

Two bare copper areas have been left near the edge of the board for fitting the additional ground wires originally connected on the underside to pin 5 of IC6 and IC8. These wires were originally required as these chips and IC7 are otherwise grounded only by means of one thin trace. As the reproduction board has an internal ground plane, these wires should no longer be required.

Zip-to-SOJ DRAM Adapter Boards

Due to concerns regarding the availability of the smaller zip DRAM chips, two adapter boards have been created to allow the use of the SOJ part found on the 837-8952 with earlier revisions. The footprints are tailored to the reproduction boards but should also be usable on originals.

Installation is reasonably self-explanatory; fit the SOJ RAM to the adapter board and use header pins or similar to install this in place of the original zip chips. Capacitor C2 may benefit from bending the legs 90 degrees so it sits to the side of the board, depending on its physical size. On both boards, it may also be useful/necessary to desolder FR5 and orient this parallel to the PCB to improve clearance. It should be fine to remove/leave off the decoupling capacitors for the zip RAM (C10, C11, C12, C13) from the main board too if this helps.

Many pins are common to all the zip chips so not all pins need to be connected to the adapter. The required pins are circled on the board. It should not harm anything to connect the others (e.g. to improve structural stability) but this may introduce some additional noise.

Additional Resources

If you require the SEGA font for producing a logo on the board, you may consider this one. Note that the author specifies that this is allowed for personal, non-commercial use only and may not be redistributed.

Thanks

  • Simon "Aergan" Lock (@Aergan) for your insights, advice, support and expert testing of the first boards.

  • Chrissy (@chris-jh) for the connect board reproduction project, support and testing.

  • Aaron Lavery (@ayyyyyyyron) for building/testing the Export/MCE2 combination.

  • Adrian Soh (@klin1309) for verifying the 837-8015/MCE1 combination.

  • Zaxour, @PointerFunction, Leo Oliveira and the rest of the Board Folk for their support and general coolness.

  • 240p Test Suite by @ArtemioUrbina was indispensible for testing and troubleshooting the boards.

Legal

As the product of this project is a replica of a proprietary product, the the author makes no claim of copyright to the schematics nor PCB layouts and releases these into the public domain, solely for the purposes of study and historical preservation.

You are free to produce PCBs based on this project's designs at your own risk and without limitation, for your own use or for sale and/or repair at a reasonable price. Attribution is appreciated. The authors are not obliged to provide support of any kind.

Under no circumstances will the authors be held responsible or liable in any way for losses, damages or costs resulting from the use of the information and/or resources of this project.

The resources are provided "as-is" without warranty of any kind, either expressed or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Parts

132
QtyValueFootprintReferences
1822nFMegaCD_Footprints:SMD_0805_HandSolderC2, C3, C4, C5, C6, C7, C10, C11, C12, C14, C15, C16, C17, C18, C19, C20 +2
15TestPointMegaCD_Footprints:Test_Point_1.5mmM0, M1, M2, M3, M4, M5, M6, M7, M8, M9, M10, M11, M12, M13, M14
1010uFMegaCD_Footprints:CP_Elec_3x5.4C41, C42, C43, C44, C45, C46, C47, C48, C49, C50
7Not usedMegaCD_Footprints:SMD_0805_HandSolderC23, C24, C26, C27, C53, C54, C55
7~MegaCD_Footprints:SMD_0805_HandSolder_NarrowFB5, FB6, FB7, FB8, FB9, FB10, FB11
6N/UMegaCD_Footprints:SMD_0805_HandSolderC22, C30, C32, C56, C57, C58
50MegaCD_Footprints:SMD_0805_HandSolderR8, R9, R10, R11, R12
44.7KMegaCD_Footprints:SMD_0805_HandSolderR1, R2, R3, R4
4~MegaCD_Footprints:FB_P7.00mmFB12, FB13, FB14, FB16
3100pFMegaCD_Footprints:SMD_0805_HandSolderC25, C28, C39
3133pFMegaCD_Footprints:SMD_0805_HandSolderC21, C31, C38
3FBMegaCD_Footprints:FB_P7.00mmFB1, FB2, FB3
2100uFMegaCD_Footprints:C_Radial_5mmC51, C52
2200pFMegaCD_Footprints:SMD_0805_HandSolderC37, C40
265256BLFP-10TMegaCD_Footprints:SOIC-28WiderIC10, IC11
2C1623MegaCD_Footprints:SOT-23-WideTR1, TR2
2MB8464A-90LMegaCD_Footprints:SOIC-28WiderIC14, IC15
2TC511664BZMegaCD_Footprints:ZIP-40IC7, IC8
2~MegaCD_Footprints:FB_SMD_LargeFB4, FB18
2~MegaCD_Footprints:EM_FilterEM1, EM3
11000pFMegaCD_Footprints:SMD_0805_HandSolderC1
1160MegaCD_Footprints:SMD_0805_HandSolderR6
12.2KMegaCD_Footprints:SMD_0805_HandSolderR5
122uFMegaCD_Footprints:SMD_0805_HandSolderC13
127C1024MegaCD_Footprints:DIP-40_W15.24mm_SocketIC4
1315-5476AMegaCD_Footprints:PQFP-80_14x20mm_P0.8mm_long_padsIC3
1315-5548/315-5632MegaCD_Footprints:PQFP-208_28x28mm_P0.5mm_WiderIC2
133pFMegaCD_Footprints:SMD_0805_HandSolderC33
1360MegaCD_Footprints:SMD_0805_HandSolderR7
150MHzOscillator:Oscillator_DIP-14OSC1
150pFMegaCD_Footprints:SMD_0805_HandSolderC29
160pFMegaCD_Footprints:SMD_0805_HandSolderC35
168HC000MegaCD_Footprints:PLCC-68-Longer_PadsIC1
174AC74MegaCD_Footprints:SOIC-14W_5.3mm_P1.27mmIC17
174HC245MegaCD_Footprints:SOIC-20W_7.5x12.8mm_P1.27mm_narrowedIC9
174HC86MegaCD_Footprints:SOIC-14W_5.3mm_P1.27mmIC12
182pFMegaCD_Footprints:SMD_0805_HandSolderC34
1?FMegaCD_Footprints:SMD_0805_HandSolderC36
1AL2032MegaCD_Footprints:Battery_no_symbolsBT1
1CON 21PMegaCD_Footprints:CON-21PCN3
1CON 25P ANGLEMegaCD_Footprints:CON-25P-ANGLECN1
1EDGE 60PMegaCD_Footprints:EDGE-60PCN2
1GREENMegaCD_Footprints:LEDLD2
1HM514270MegaCD_Footprints:SOJ-40-ExportIC5
1LC8951MegaCD_Footprints:PQFP-80_14x20mm_P0.8mm_long_padsIC13
1MB3790MegaCD_Footprints:SOIC-16W_5.3x10.2mm_P1.27mmIC6
1MB8464A-10LMegaCD_Footprints:SOIC-28WiderIC16
1REDMegaCD_Footprints:LEDLD1
1~MegaCD_Footprints:FB_P9.00mmFB15
1~MegaCD_Footprints:FB_P5.00mmFB17
1~MegaCD_Footprints:EM_Filter_FlippedEM2

More from Board-Folk/MegaCD-Main-BD

3
  • 4 layers188.9 × 92 mmMegaCD, the printed circuit board in 3D

    MegaCD

    Board-Folk/MegaCD-Main-BD

    Reproductions of main board PCBs for Sega's Mega CD/Sega CD add-on for the Mega Drive/Genesis console.

    117 parts60
  • 4 layers188.9 × 92 mmMegaCD, the printed circuit board in 3D

    MegaCD

    Board-Folk/MegaCD-Main-BD

    Reproductions of main board PCBs for Sega's Mega CD/Sega CD add-on for the Mega Drive/Genesis console.

    107 parts60
  • 4 layers57.9 × 26 mmMegaCD, the printed circuit board in 3D

    MegaCD

    Board-Folk/MegaCD-Main-BD

    Reproductions of main board PCBs for Sega's Mega CD/Sega CD add-on for the Mega Drive/Genesis console.

    7 parts60

Similar boards

  • 2 layersVideoBoard, the printed circuit board in 3D

    VideoBoard

    Cptscorcher/Excallibur-64

    A reimagining of the seminal Excalibur 64 Computer

    126 partsGPL-3.0
  • 2 layers233.4 × 280 mmCft board0, the printed circuit board in 3D

    Cft board0

    alexiosc/cft

    The CFT homebrew minicomputer

    299 parts6GPL-3.0
  • 2 layers90.2 × 91.3 mmPb v1, the printed circuit board in 3D

    Pb v1

    ossm-rs/ossm-rs-powerboard

    Power management PCB for AIM family motors, designed to pair with the Industrial ESP32-S3-RS485-CAN control board by Waveshare and run with OSSM-RS software.

    58 parts2
  • 4 layers85 × 56 mmPiVI, the printed circuit board in 3D

    PiVI

    kuba2k2/PiVI

    A small Pi-sized single board computer for your car

    289 partsGPL-3.0
  • 2 layers245.1 × 160 mm8-Bit CPU 32k, the printed circuit board in 3D

    8-Bit CPU 32k

    slu4coder/Minimal-64x4-Home-Computer

    My DIY TTL home computer with VGA and PS/2 and 4x the processing power of a Commodore C64 or Apple II.

    139 parts326
  • 2 layers191.8 × 121.3 mm8-Bit CPU 32k, the printed circuit board in 3D

    8-Bit CPU 32k

    slu4coder/Minimal-UART-Computer-1-2

    Legacy: Version 1 and 2 of my TTL-only CPU featuring UART I/O, an expansion port, 512KB SSD at up to 10MHz clock speed

    109 parts184
  • 2 layers306.1 × 130.2 mm8-Bit CPU 32k, the printed circuit board in 3D

    8-Bit CPU 32k

    slu4coder/Minimal-64-Home-Computer

    Legacy: Full TTL-only home computer with VGA and PS/2 and twice the processing power of a Commodore 64

    132 parts94

Questions

How big is the MegaCD PCB?

It measures 188.9 × 92 mm and has 4 copper layers, 1.6 mm thick.

What parts does the MegaCD use?

132 parts, built around the 74HC245D, 74AC74M, 74HC86D and CL10B474KA8NNN. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the MegaCD KiCad files?

From the Board-Folk/MegaCD-Main-BD repository on GitHub, at the commit this page was made from: the board is MegaCD-837-8952-Export/MegaCD.kicad_pcb and its schematic MegaCD-837-8015-01-Rev1-MCE2/MegaCD.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the MegaCD design in my own project?

Its repository states no licence, so its author keeps all rights: ask Board-Folk before reusing the design.