

Spw router
SpaceWire router using Artix-7 FPGA
- Size
- 100 × 85 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 77
- Nets
- 239
- Pads
- 574
- Tracks, vias
- 1,350, 125
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 16 Aug 2024
- Updated
- 5 Sep 2024
Overview
Spw router is an open-source printed circuit board by Bendi11, from the Bendi11/spw-router repository on GitHub. It is a 4-layer board of 100 × 85 mm with 77 parts on 239 nets, routed with 1,350 tracks and 125 vias.
It is built around the IS25LP064D-JBLE-TR, TPS54331DR-JSM and AP7361C-10E, with the TSB008A2526A, CD-1206-SMT and DC-044A-20A among its other parts. Its parts include 41 capacitors, 10 connectors, 9 resistors, 6 ICs and 2 switches. It belongs with the fPGA and programmable logic boards and the STM32 and FPGA and CPLD boards of this library.
Main components
6IS25LP064D-JBLE-TR
SOIC-8-208mil-40℃~+105℃ 100,000 cycles 166MHz 2.3V~3.6V 20 Years 200us 64Mbit 8uA Power-on reset、Hardware write protection、Software write protection、Write enable latch、Power lock protection SPI SOIC-8-208mil NOR FLASH ROHSISSINOR FLASHTPS54331DR-JSM
SOP-8-40℃~+125℃ 1 2mA 3A 4.5V~40V 400kHz Adjustable Buck Built-in No Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting Step-down type SOP-8 DC-DC Converters ROHSJSMSEMIDC-DC ConvertersAP7361C-10E
SOT-223-3-40℃~+85℃@(Ta) 1 1A 1V 60uA 6V 75dB@(1kHz) 840mV@(1A) Fixed Over Current Protection、Over Temperature Protection、Enable、Short Circuit Protection Positive SOT-223-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTSB008A2526A
SMD,6x3.5mm12V 2.5mm 2.6N 3.5mm 50mA 6mm No Rectangular Button SPST Surface Mount,Vertical White Without Bracket SMD,6x3.5mm Tactile Switches ROHSBZCNTactile SwitchesCD-1206-SMT
SMD,D12xL9mm-40℃~+70℃ 12mm 2.4kHz 40mA 4V~8V 5V 85dB 9.5mm Electromagnetic Passive (Externally Driven) SMD SMD,D12xL9mm Buzzers ROHSCUIBuzzersDC-044A-20A
插件-20℃~+70℃ 2mm 30V 5.9mm 5A DC Power Jack Right Angle 插件 DC Power Connectors ROHSHRO ElectronicsDC Power Connectors
README
README.md8 Port SpaceWire Router
A hobby-grade SpaceWire router aiming for full ECSS-E-ST-50-12C compliance utilizing a Xilinx Artix 7 FPGA.
Hardware Development
KiCad schematics and board design files for the board are stored in the hw/board directory.
Custom footprints and 3D models are placed into the hw/models directory.
FPGA
Verilog sources are located in the rtl/src directory, and both the synthesis and simulation
processes are managed by CMake.
Currently, the FPGA bitstream is generated with a fully open-source
yosys + nextpnr-xilinx flow,
and does not require the Xilinx Vivado software.
Paths to the required tools must currently be provided in an env.cmake file located in the
rtl/cmake directory, which must set the following:
| Variable Name | Description |
|---|---|
| YOSYS | Path to the yosys binary |
| NEXTPNR_XILINX | Path to the nextpnr-xilinx binary, usually found at the root of the nextpnr-xilinx repository after building |
| XRAY_DB_DIR | Path to the Project X-Ray database |
| XRAY_FASM2FRAMES | Command to use the fasm2frames tool provided in Project X-Ray. This python script may have to run in Project X-Ray's virtual environment, so this variable is typically "${PRJXRAY_DIR}/env/bin/python3" "${XRAY_DIR}/utils/fasm2frames.py" |
| XRAY_XC7FRAMES2BIT | Path to the Project X-Ray's xc7frames2bit binary, usually in ${PRJXRAY_DIR}/build/tools/ |
Example env.cmake
set(NEXTPNR_XILINX_DIR "$ENV{HOME}/nextpnr-xilinx")
set(XRAY_DIR "$ENV{HOME}/prjxray")
set(XRAY_DB_DIR "${NEXTPNR_XILINX_DIR}/xilinx/external/prjxray-db")
set(YOSYS "yosys")
set(NEXTPNR_XILINX "${NEXTPNR_XILINX_DIR}/nextpnr-xilinx")
set(XRAY_FASM2FRAMES "${XRAY_DIR}/env/bin/python3" "${XRAY_DIR}/utils/fasm2frames.py")
set(XC7FRAMES2BIT "${XRAY_DIR}/build/tools/xc7frames2bit")Design verification is performed with Verilator, with simulation
shims for Xilinx hard IP located in the rtl/sim/verilog directory.
STM32 Software
TODO
Parts
77| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 470n | Capacitor_SMD:C_0805_2012Metric | C3, C4, C14, C18, C19, C23, C26, C28, C32, C33, C35, C37, C39, C40 |
| 11 | 4u7 | Capacitor_SMD:C_0805_2012Metric | C15, C16, C21, C22, C25, C27, C30, C34, C36, C38, C41 |
| 9 | 47u | Capacitor_SMD:C_0805_2012Metric | C2, C5, C6, C7, C8, C9, C17, C20, C31 |
| 8 | ~ | DE9:DE9_Pins | J3, J4, J5, J6, J7, J8, J9, J10 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 3 | 10k | Resistor_SMD:R_0805_2012Metric | R1, R2, R11 |
| 3 | 4k7 | Resistor_SMD:R_0805_2012Metric | R4, R7, R10 |
| 2 | 100n | Capacitor_SMD:C_0805_2012Metric | C1, C12 |
| 2 | 100u | Capacitor_SMD:C_0805_2012Metric | C24, C29 |
| 2 | Conn_ARM_JTAG_SWD_10 | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical | J1, J2 |
| 2 | TSB008A2526A | EasyEDA:SW-SMD_L6.0-W3.5-LS8.0 | SW1, SW2 |
| 1 | 0 | Resistor_SMD:R_0805_2012Metric | R8 |
| 1 | 10n | Capacitor_SMD:C_0805_2012Metric | C10 |
| 1 | 330 | Resistor_SMD:R_0805_2012Metric | R3 |
| 1 | 41k | Resistor_SMD:R_0805_2012Metric | R9 |
| 1 | 47p | Capacitor_SMD:C_0805_2012Metric | C13 |
| 1 | 510p | Capacitor_SMD:C_0805_2012Metric | C11 |
| 1 | 6u8 | EasyEDA:IND-SMD_L11.6-W10.1 | L1 |
| 1 | AP7361C-10E | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U4 |
| 1 | AP7361C-18SP-13 | Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm_ThermalVias | U3 |
| 1 | CD1206 | Diode_SMD:D_1206_3216Metric | D1 |
| 1 | DC-044A-20A | EasyEDA:DC-IN-TH_DC-044A-20A | DC1 |
| 1 | IS25LP064D-JBLE-TR | EasyEDA:SOIC-8_L5.3-W5.3-P1.27-LS7.9-BL | U2 |
| 1 | STM32F302CBTx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP1 |
| 1 | TPS54331DR | Snapeda:SOIC127P599X175-8N | U5 |
| 1 | TYPE-C 16PIN 2MD(073) | EasyEDA:USB-C-SMD_TYPE-C-6PIN-2MD-073 | USB1 |
| 1 | XC7A35T-FTG256 | Package_BGA:Xilinx_FTG256 | U6 |
Similar boards
- 2 layers49.8 × 49.9 mm

- 4 layers101.6 × 53.3 mm

- 4 layers95.9 × 46 mm

Dragon 4L R02
CyberSaiyanIT/why2025-badge
Cyber Saiyan community has designed and developed a special gadget for WHY2025. The badge was designed to recall the dragon spheres, and is an updated version of RomHack Camp 2022 badge, both in term of design and…
127 parts10MIT - 2 layers98.6 × 98.6 mm

ReflowMate
Omar-Magdy0/ReflowMate
To start small , grow big. current focus is mainly on providing : Digital Soldering iron support Hot air gun support 3d printable Accessories
97 parts1 - 4 layers79.7 × 33.2 mm

- 2 layers88 × 60 mm

CamRover pcb v1 1
aravindjayan/CamRover
PCB and bringup codebase for an ESP32-S3 based wheeled robot with an OV2640 camera. Built for IIT Palakkad EE4505 course.
66 parts - 2 layers220 × 120 mm

- 4 layers85 × 56 mm

Questions
How big is the Spw router PCB?
It measures 100 × 85 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Spw router use?
77 parts, built around the IS25LP064D-JBLE-TR, TPS54331DR-JSM, AP7361C-10E and TSB008A2526A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Spw router KiCad files?
From the Bendi11/spw-router repository on GitHub, at the commit this page was made from: the board is hw/board/board.kicad_pcb and its schematic hw/board/PDN.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Spw router design in my own project?
Its repository states no licence, so its author keeps all rights: ask Bendi11 before reusing the design.