Skip to the content
2 layers57 × 52 mmPCB Design Übung, the printed circuit board in 3D

STM32 Board Design + Firmware + Desktop App

Size
57 × 52 mm
Copper layers
2
Thickness
1.6 mm
Parts
66
Nets
58
Pads
227
Tracks, vias
526, 78
Pours
5
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
21 May 2026
Updated
14 Jul 2026

Overview

PCB Design Übung is an open-source printed circuit board by BenWeckend, from the BenWeckend/STM32F103-Board-Design repository on GitHub. It is a 2-layer board of 57 × 52 mm with 66 parts on 58 nets, routed with 526 tracks and 78 vias.

It is built around the STM32F103C8T6, TJA1051T/3/1 and BME280, with the AMS1117-3.3, ESD9B3.3ST5G and NUP2105LT1G among its other parts. Its parts include 18 capacitors, 15 resistors, 10 diodes, 4 ICs and 2 connectors. It belongs with the STM32 boards of this library.

Main components

6

README

README.md

STM32F103 Board Design

Überblick

Hardware-Referenzdesign und Firmware für ein Übungs-Entwicklungsboard auf Basis des STM32F103C8T6 mit CAN, USB, I²C (BME280) und weiterer Peripherie.

Das Repository enthält:

  • KiCad-Schaltplan und PCB-Design
  • Gerber- und Fertigungsdaten
  • Stückliste (BOM)
  • STM32CubeIDE Firmware-Projekt
  • Tauri Desktop-Anwendung zur Kommunikation mit dem Board

Hardware

Schaltplan

STM32F103 Schaltplan

Vollständiger Schaltplan des STM32F103-Boards mit CAN, USB, Spannungsversorgung und BME280-Sensor.

3D-Ansicht der Platine

3D PCB Rendering

3D-Vorschau der fertig bestückten Leiterplatte aus KiCad.


Projektstruktur

OrdnerBeschreibung
kicad/Schaltplan, PCB-Layout und Fertigungsdaten
firmware/STM32CubeIDE-Projekt
tauri-app/Desktop-Anwendung (Rust + Frontend)

Hauptfunktionen

Mikrocontroller

  • STM32F103C8T6 (LQFP48)

Kommunikation

  • CAN-Bus über TJA1051
  • USB Micro-B Device Interface

Sensorik

  • BME280 (I²C)

    • Temperatur
    • Luftdruck
    • Luftfeuchtigkeit

Spannungsversorgung

  • AMS1117-3.3
  • Onboard 3.3V-Regler

Debugging & Programmierung

  • SWD Header
  • ST-Link kompatibel
  • STM32CubeProgrammer kompatibel

Parts

66
QtyValueFootprintReferences
7100nCapacitor_SMD:C_0402_1005MetricC1, C2, C3, C4, C9, C16, C17
44k7Resistor_SMD:R_0402_1005MetricR5, R6, R12, R13
4MountingHoleMountingHole:MountingHole_2.1mmH1, H2, H3, H4
310ohmResistor_SMD:R_0402_1005MetricR7, R8, R9
3Conn_01x03Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalCAN1, CAN2, CAN3
3LED_BLED_SMD:LED_0603_1608MetricD4, D7, D8
20.1kResistor_SMD:R_0402_1005MetricR4, R14
2100pCapacitor_SMD:C_0402_1005MetricC18, C19
210kResistor_SMD:R_0402_1005MetricR1, R2
210pCapacitor_SMD:C_0603_1608MetricC10, C11
21uCapacitor_SMD:C_0603_1608MetricC7, C8
222uCapacitor_SMD:C_0805_2012MetricC12, C13
260ohmResistor_SMD:R_0603_1608MetricR10, R11
2Conn_01x04_PinConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalSPI&UART1, SWD
2ESD9B3.3ST5GDiode_SMD:D_SOD-923D2, D3
2Jumper_2_BridgedTestPoint:TestPoint_2Pads_Pitch2.54mm_Drill0.8mmJP1, JP2
110nCapacitor_SMD:C_0402_1005MetricC6
110uCapacitor_SMD:C_0805_2012MetricC5
1120RInductor_SMD:L_0603_1608MetricFB1
116MHzCrystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
11N5818Diode_THT:D_DO-41_SOD81_P10.16mm_HorizontalD6
11k5Resistor_SMD:R_0402_1005MetricR3
1220ohmResistor_SMD:R_0402_1005MetricR15
14n7Capacitor_SMD:C_0603_1608MetricC20
1AMS1117-3.3Package_TO_SOT_SMD:SOT-223-3_TabPin2U2
1BME280Package_LGA:Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumberingU3
1Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ5
1Conn_01x07Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_VerticalI2C&GPIO
1Conn_01x08Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_VerticalUART&SPI
1LED-GreenLED_SMD:LED_0603_1608MetricD1
1LED_GLED_SMD:LED_0603_1608MetricD9
1LED_RLED_SMD:LED_0603_1608MetricD10
1NUP2105LT1GPackage_TO_SOT_SMD:SOT-23D5
1STM32F103C8T6Package_QFP:LQFP-48_7x7mm_P0.5mmU1
1SW_PushButton_Switch_THT:SW_PUSH_6mmSW2
1SW_SPDTButton_Switch_SMD:SW_SPDT_PCM12SW1
1TJA1051T-3Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU4
1USB_B_MicroConnector_USB:USB_Micro-B_Wuerth_629105150521J1

Similar boards

  • 4 layers99.5 × 69 mmPump controller reva, the printed circuit board in 3D

    Pump controller reva

    UWARG/pump-controller-hardware

    Hardware for Competition 2026 Water Pump Controller on Project Valkyrie

    244 parts
  • 2 layers100 × 66 mmEcocar on boarding Rev4, the printed circuit board in 3D

    Ecocar on boarding Rev4

    elamey413/EcoCar_Onboarding

    Here is my onboarding project for EcoCar. It is a STM32F103C8T6 based PCB that is able to measure several important data points for drone flying.

    52 parts1
  • 2 layers43 × 33 mmSTM32, the printed circuit board in 3D

    STM32

    Adityasc9/STM32-Custom-PCB

    Hardware design files for a custom STM32 development board created in KiCad.

    39 parts
  • 2 layers42.3 × 43.9 mmIoT Weather Station Circuit, the printed circuit board in 3D

    IoT Weather Station Circuit

    Ezerwald/stm32-kicad-weather-station

    KiCad-based PCB project for an STM32-powered IoT weather station with environmental sensing, real-time clock support, battery charging, and e-paper display connectivity.

    46 partsMIT
  • 4 layers160 × 117.5 mmDaveecu2, the printed circuit board in 3D

    Daveecu2

    miata-bot/daveecu2

    Speeduino Mainboard designed for NA Maita chassis

    249 parts3
  • 2 layers122.5 × 87.6 mmControllerCircuit, the printed circuit board in 3D

    ControllerCircuit

    stuartpittaway/diyBMSv4

    Version 4 of the diyBMS

    113 parts1.1k
  • 2 layers116.8 × 106.7 mm-1, the printed circuit board in 3D

    -1

    CYT-ks/-1

    zuoye

    51 parts1

Questions

How big is the PCB Design Übung PCB?

It measures 57 × 52 mm and has 2 copper layers, 1.6 mm thick.

What parts does the PCB Design Übung use?

66 parts, built around the STM32F103C8T6, TJA1051T/3/1, BME280 and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the PCB Design Übung KiCad files?

From the BenWeckend/STM32F103-Board-Design repository on GitHub, at the commit this page was made from: the board is kicad/PCB Design Übung.kicad_pcb and its schematic kicad/PCB Design Übung.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the PCB Design Übung design in my own project?

Its repository states no licence, so its author keeps all rights: ask BenWeckend before reusing the design.