Skip to the content
2 layers80 × 55 mmLora169, the printed circuit board in 3D

Carte adaptatrice qui transforme le module Ebyte E22-170M30S (SMD, pads en bord) en module DIP enfichable via deux pin headers 1×11 broches au pas 2,54 mm.

Size
80 × 55 mm
Copper layers
2
Thickness
1.6 mm
Parts
7
Nets
19
Pads
54
Tracks, vias
99, 0
Pours
2
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
1 May 2026
Updated
3 May 2026

Overview

Lora169 is an open-source printed circuit board by Alixpat, from the Alixpat/lora169 repository on GitHub. It is a 2-layer board of 80 × 55 mm with 7 parts on 19 nets, routed with 99 tracks and 0 vias.

Its parts include 2 connectors and 1 IC. It belongs with the ESP32 boards of this library.

README

hardware/breakout-e22/README.md

Breakout E22 (carte fille)

Carte adaptatrice qui transforme le module Ebyte E22-170M30S (SMD, pads en bord) en module DIP enfichable via deux pin headers 1×11 broches au pas 2,54 mm. Permet de changer de fréquence (170 / 400 / 900 MHz) sur la carte mère sans dessouder.

Conception

Design propre fait pour ce projet, avec :

  • 1× module E22-xxxM30S (mécanique commune à 170/400/900 MHz)
  • 2× condensateurs de découplage 100 nF + 10 µF (céramique X7R 0805) au plus près des pins VCC, pour absorber le pic TX 30 dBm (~620 mA)
  • 2× pin headers 1×11 broches au pas 2,54 mm sur les bords longs
  • VCC alimenté en 5 V depuis VBUS du XIAO côté carte mère, pour permettre la pleine puissance 30 dBm hardware
  • Plan de masse continu sur la face arrière

Caractéristiques techniques

  • Format PCB : 40,6 × 46,3 mm (compact, à peine plus large que le module E22 lui-même de 24 × 38,5 mm)
  • Espacement entre les deux pin headers J1/J2 : 32,1 mm centre à centre — à respecter sur la carte mère (embases femelles 1×11)
  • Pistes signal en 0,2 mm, piste alim +5V en 0,4 mm pour absorber le pic 620 mA en TX 30 dBm
  • Pads GND en pleine connexion à la zone GND (sans thermal relief) pour minimiser l'inductance de retour

Valeurs de découplage — sources

Le combo 100 nF + 10 µF céramique 0805 est validé par la pratique de plusieurs designs publics éprouvés à 30 dBm voire 33 dBm :

Ni la datasheet E22 ni les notes Semtech (AN1200.37, AN1200.40) ne donnent de valeurs explicites pour le découplage externe d'un module E22 fini — la datasheet recommande juste un « external ceramic filter capacitor ». Les 100 nF + 10 µF sont donc retenus comme convention d'industrie validée empiriquement.

Mapping J1 / J2 (côté carte mère)

Pin headerBrocheSignalPad E22
J21-5, 11GND1-5, 11
J26RXEN6
J27TXEN7
J28NC (DIO2)8
J29-10+5V (VCC)9-10
J11, 9, 11GND12, 20, 22
J12DIO113
J13BUSY14
J14NRST15
J15MISO16
J16MOSI17
J17SCK18
J18NSS19
J110NC (ANT)21 (sortie RF, non utilisée en IPEX)

Statut

  • DRC : 0 erreur, 0 unconnected
  • Gerbers générés : breakout-e22-gerbers.zip
  • Prêt à fabriquer chez JLCPCB / PCBWay

Parts

7
QtyValueFootprintReferences
2Conn_01x11Connector_PinSocket_2.54mm:PinSocket_1x11_P2.54mm_VerticalJ1, J2
1XIAO-ESP32-S3-DIPSeeed_XIAO:XIAO-ESP32-S3-DIPU1

The 3 most common of 7 parts.

More from Alixpat/lora169

1
  • 2 layers40.6 × 46.3 mmBreakout e22, the printed circuit board in 3D

    Breakout e22

    Alixpat/lora169

    Carte adaptatrice qui transforme le module Ebyte E22-170M30S (SMD, pads en bord) en module DIP enfichable via deux pin headers 1×11 broches au pas 2,54 mm.

    5 parts

Similar boards

  • 2 layersEncoder, the printed circuit board in 3D

    Encoder

    byrantech/laptop

    anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

    7 parts4.3kMIT
  • 2 layers40 × 20 mmSensor smd, the printed circuit board in 3D

    Sensor smd

    scottbez1/splitflap

    DIY split-flap display

    7 parts4.2k
  • 2 layers19.8 × 30 mmZ limit, the printed circuit board in 3D

    Z limit

    opulo-inc/lumenpnp

    The LumenPnP is an open source pick and place machine.

    7 parts3.7k
  • 2 layers35.6 × 58.2 mmDisplay Carrier, the printed circuit board in 3D

    Display Carrier

    AxxAxx/AxxSolder

    STM32 Based soldering station for JBC cartridges, 9-24 VDC and USB-PD power

    7 parts1.7kGPL-3.0
  • 2 layers20.3 × 16.3 mmMap MPX, the printed circuit board in 3D

    Map MPX

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    7 parts1.2k
  • 2 layers26 × 44 mmCompact carrier board, the printed circuit board in 3D

    Compact carrier board

    jamro/tiny-engineer

    A small desktop robot that brings an AI coding assistant to life, physically acting out when it reads files, thinks, writes code, and finishes work.

    7 parts1.1k
  • 2 layers26.4 × 53.8 mmAtari pickup, the printed circuit board in 3D

    Atari pickup

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    7 parts1kGPL-3.0
  • 2 layersRj45 breakout, the printed circuit board in 3D

    Rj45 breakout

    rene-dev/stmbl

    AC Servo Driver for STM32F4

    7 parts990GPL-3.0

Questions

How big is the Lora169 PCB?

It measures 80 × 55 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Lora169 use?

7 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Lora169 KiCad files?

From the Alixpat/lora169 repository on GitHub, at the commit this page was made from: the board is hardware/lora169.kicad_pcb and its schematic hardware/breakout-e22/breakout-e22.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Lora169 design in my own project?

Its repository states no licence, so its author keeps all rights: ask Alixpat before reusing the design.