Skip to the content
2 layers49.3 × 44.8 mmATmega32, the printed circuit board in 3D

Custom ATmega328P development board designed from scratch using KiCad.

Size
49.3 × 44.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
17
Nets
28
Pads
82
Tracks, vias
190, 0
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
27 Jul 2026
Updated
27 Jul 2026

Overview

ATmega32 is an open-source printed circuit board by Agarwal-Amogh, from the Agarwal-Amogh/ATmega328P-Development-Board repository on GitHub. It is a 2-layer board of 49.3 × 44.8 mm with 17 parts on 28 nets, routed with 190 tracks and 0 vias.

It is built around the ATMEGA328P-PU. Its parts include 4 capacitors, 3 resistors, 2 diodes, 1 IC and 1 switch. It belongs with the microcontroller boards boards and the AVR (ATmega, ATtiny) boards of this library.

Main components

1

README

README.md

ATmega328P-Development-Board

A custom ATmega328P development board designed from scratch using KiCad.

This project was created to understand the complete hardware design process behind AVR microcontrollers instead of relying on pre-built Arduino boards. The board exposes all GPIO pins through headers, includes an ISP programming interface, a crystal oscillator, reset circuitry, power regulation connections, and status LEDs.


Images

atmega_schematic atmega_pcb atmega_3d

Features

  • ATmega328P-PU (DIP-28)
  • 16 MHz external crystal oscillator
  • Reset push button with pull-up resistor
  • ISP (In-System Programming) header
  • Power LED
  • User LED connected to PB5 (Arduino D13)
  • Digital GPIO headers (PORTB & PORTD)
  • Analog GPIO header (PORTC)
  • Power header (+5V & GND)
  • Decoupling capacitors
  • Single-layer PCB design
  • Ground plane
  • Designed and verified using KiCad

Hardware Used

ComponentDescription
ATmega328P-PUAVR 8-bit Microcontroller
16 MHz CrystalSystem clock
22 pF CapacitorsCrystal load capacitors
100 nF CapacitorsPower supply decoupling
Push ButtonReset
LEDsPower indicator & User LED
Pin HeadersGPIO, Power and ISP connections

PCB

The PCB was designed as a single-layer through-hole board to simplify manufacturing and improve understanding of PCB layout fundamentals.

Design considerations included:

  • Keeping crystal traces as short as possible
  • Placing decoupling capacitors close to the power pins
  • Ground plane for improved power integrity
  • Clean component placement before routing
  • Passing KiCad Design Rule Check (DRC) with zero errors and zero warnings

Skills Demonstrated

  • Schematic Capture
  • PCB Design
  • Component Placement
  • Ground Plane Design
  • Design Rule Check (DRC)
  • AVR Hardware Design
  • ISP Programming Interface Design
  • Power Distribution
  • Crystal Oscillator Layout

Software

  • KiCad

Future Work

This board will be used as the hardware platform for future bare-metal AVR projects, including:

  • GPIO Driver
  • Button Driver
  • Timer Driver
  • UART Driver
  • SPI Driver
  • I²C Driver
  • ADC Driver
  • Interrupts
  • Bootloader
  • Complete Embedded Systems Projects

Parts

17
QtyValueFootprintReferences
2100nCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC1, C4
222pCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC2, C3
2330Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR2, R3
2Conn_01x06Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalANALOG(A0-A5), DIGITAL(D8-D13)
2LEDLED_THT:LED_D5.0mmD1_PWR, D2_USER
110kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1
116MhzCrystal:Crystal_HC49-U_VerticalY1
1ATmega328P-PPackage_DIP:DIP-28_W7.62mmU1
1AVR-ISP-6Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_VerticalISP HEADER
1Conn_01x04Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalPWR_OUT
1Conn_01x08Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_VerticalDIGITAL(D0-D7)
1SW_PushButton_Switch_THT:SW_PUSH_6mmSW1

Similar boards

  • 2 layers68.8 × 53.6 mmZArduino, the printed circuit board in 3D

    ZArduino

    zmaker/arduino_cookbook

    gli sketch del nuovo progetto Arduino Cookbook e dei video di YouTube

    46 parts269
  • 2 layers76.3 × 122.8 mmDiscipad pcb, the printed circuit board in 3D

    Discipad pcb

    coseyfannitutti/discipad

    17-key numpad assembled with only through hole components, including usb type-c

    63 parts221GPL-3.0
  • 2 layers111.3 × 106.4 mmSuper Sixteen v1, the printed circuit board in 3D

    Super Sixteen v1

    matthewcieplak/super-sixteen

    Code and schematics for the Super Sixteen Eurorack sequencer

    141 parts171
  • 2 layers247.6 × 99.2 mmRomeo pcb, the printed circuit board in 3D

    Romeo pcb

    coseyfannitutti/romeo

    Staggered 40% keyboard pcb that can be assembled with only through hole components, including USB Type-C

    138 parts148GPL-3.0
  • 2 layers90 × 140 mmDrumkid, the printed circuit board in 3D

    Drumkid

    mattybrad/drumkid

    Version 4 was the first successful working design, with full code, schematics, Gerbers, etc available on GitHub.

    70 parts137
  • 2 layers238.1 × 375.5 mmFramework, the printed circuit board in 3D

    Framework

    stevennguyen/framework

    Ortholinear keyboard with a knob

    197 parts131
  • 2 layersLM80C R6, the printed circuit board in 3D

    LM80C R6

    leomil72/LM80C

    A Z80-based homebrew computer withTMS9918, AY-3-8910, Z80 CTC, Z80 PIO, and Z80 SIO

    153 parts123GPL-3.0
  • 2 layers145.3 × 44.5 mmScout, the printed circuit board in 3D

    Scout

    oskitone/scout

    3D-printed, Arduino-compatible, 17-key mono synth. Squeeeee!

    48 parts114

Questions

How big is the ATmega32 PCB?

It measures 49.3 × 44.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the ATmega32 use?

17 parts, built around the ATMEGA328P-PU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ATmega32 KiCad files?

From the Agarwal-Amogh/ATmega328P-Development-Board repository on GitHub, at the commit this page was made from: the board is ATmega32_KiCad/ATmega32.kicad_pcb and its schematic ATmega32_KiCad/ATmega32.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the ATmega32 design in my own project?

Its repository states no licence, so its author keeps all rights: ask Agarwal-Amogh before reusing the design.