

Main pcb
a 6 axis robotic arm
- Size
- 113.8 × 76.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 34
- Nets
- 89
- Pads
- 191
- Tracks, vias
- 494, 19
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 10 Jun 2026
- Updated
- 10 Oct 2026
Overview
Main pcb is an open-source printed circuit board by AdityaCoppisetti, from the AdityaCoppisetti/robotic-arm repository on GitHub. It is a 2-layer board of 113.8 × 76.9 mm with 34 parts on 89 nets, routed with 494 tracks and 19 vias.
Its parts include 6 capacitors, 6 resistors, 6 switches and 3 connectors.
README
README.md6-Axis Robotic Arm
This project is a custom-built 6-axis robotic arm that I designed and built from the ground up. The arm has six degrees of freedom thus the 6DOF , I designed the mechanical parts myself and used a combination of 3D printing, custom gears ,and almost each joint is a planetary mechanism since i really wanted to learn that and i learnt that in onshape . The gripper usse MG996R V17 servo
The control side of the project is a custom pcb which is handled by a custom arduino uno nano that i made . the main pcb usees a4988 stepper motor drivers to drive each and every motor and the servo motor for the gripper i have connected directly . The plan is to use forward and inverse kinematics to move to a specific point instead of manually controlling every joint.
One of the things I want to experiment with later is turning the arm into a 3D printer by replacing the gripper with a printing head. This would make the robot more than just a robotic arm and i could then print alot of stuff from a arm that itself was 3d printed bahahahhahahaa
There will probably be a lot of redesigns, and ill keep updating the journal.md of this repo for that
i designed this robotic arm in onshape,
joint 1 - 5 uses planetary gear mechanism where the sun gear is attached to the nema 17 motor
and then ive made the claw/ gripper which uses a servo motor attached to a spur gear which move yet 2 another spur gears
how to assemble
print the given step files , modify them if you want to
and then look at the assembled version and piece everything together. i will be documenting my proccess aswell when i print the parts.
how to assemble electronic part of project
when you get the main pcb and then the microcontroller pcb you take the stencil and then use that stencil to apply solder paste. and then you remove the stencil and place each component by looking at the nicely labelled pcb
and then by using a hot air gun or a hotplate , reflow the solder
hot to assemble the main board pcb
you take the pcb and using a soldering iron just solder the required amount of female or male pinheaders ( 2.57mm exactly)
here is a mockup i nade using onshape of how the main pcb should look like after you assemlbe it
Parts
34| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100uF | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C1, C2, C3, C4, C5, C6 |
| 6 | Conn_01x04_Pin | Connector_PinHeader_2.00mm:PinHeader_1x04_P2.00mm_Vertical | BASE1, Joint1, Joint2, Joint3, Joint4, Joint5 |
| 6 | Pololu_Breakout_A4988 | Module:Pololu_Breakout-16_15.2x20.3mm | A1, A2, A3, A4, A5, A6 |
| 6 | R | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | R1, R2, R3, R4, R5, R6 |
| 2 | Conn_01x15_Pin | Connector_PinHeader_2.54mm:PinHeader_1x15_P2.54mm_Vertical | J1, J2 |
| 1 | Jack-DC | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J3 |
| 1 | Motor_Servo | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | M1 |
| 1 | joint 1 | Connector_PinHeader_1.27mm:PinHeader_1x02_P1.27mm_Vertical | SW1 |
| 1 | joint2 | Connector_PinHeader_1.27mm:PinHeader_1x02_P1.27mm_Vertical | SW2 |
| 1 | joint3 | Connector_PinHeader_1.27mm:PinHeader_1x02_P1.27mm_Vertical | SW3 |
| 1 | joint4 | Connector_PinHeader_1.27mm:PinHeader_1x02_P1.27mm_Vertical | SW4 |
| 1 | joint6 | Connector_PinHeader_1.27mm:PinHeader_1x02_P1.27mm_Vertical | SW6 |
| 1 | joints5 | Connector_PinHeader_1.27mm:PinHeader_1x02_P1.27mm_Vertical | SW5 |
More from AdityaCoppisetti/robotic-arm
2- 4 layers44.8 × 20.1 mm

- 2 layers160.4 × 88.9 mm

Similar boards
- 2 layers142.5 × 106.4 mm

- 2 layers26 × 30 mm

Microcontroller
FrameworkComputer/ExpansionCards
Reference designs and documentation to create Expansion Cards for the Framework Laptop
34 parts1.1kCC-BY-4.0 - 2 layers171.2 × 72.9 mm

Amiga gfxcard old
mntmn/amiga2000-gfxcard
MNT VA2000, an Open Source Amiga 2/3/4000 Graphics Card (Zorro II/III), written in Verilog
34 parts1k - 2 layers53.5 × 62.5 mm

Led matrix
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
34 parts915 - 2 layers45 × 26 mm

- 2 layers41.7 × 25.7 mm

Headphones flex pcb rigid
strangeparts/niubi-headphones
Flexible circuit board design for adding a headphone jack to an iPhone 7
34 parts493MIT - 2 layers18.8 × 16.3 mm

- 2 layers127 × 69.9 mm

Ezcgi
baldengineer/bit-preserve
Project for capturing vintage, classic, aka old computer schematics in KiCad.
34 parts446
Questions
How big is the Main pcb PCB?
It measures 113.8 × 76.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Main pcb use?
34 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Main pcb KiCad files?
From the AdityaCoppisetti/robotic-arm repository on GitHub, at the commit this page was made from: the board is electricals/main pcb.kicad_pcb and its schematic electricals/arduino nano.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Main pcb design in my own project?
Its repository states no licence, so its author keeps all rights: ask AdityaCoppisetti before reusing the design.