Skip to the content
2 layersHalfduplextranslator, the printed circuit board in 3D

Halfduplextranslator

AM1k21/ESP32-CRSF-Relay

Project for extension of communication range of a ELRS radio, a CRSF Relay node, that using a elrs receiver, elrs transmitter and ESP32 forwards CRSF frames.

Copper layers
2
Thickness
1.6 mm
Parts
4
Nets
11
Pads
30
Tracks, vias
47, 0
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
22 Dec 2025
Updated
8 Apr 2026

Overview

Halfduplextranslator is an open-source printed circuit board by AM1k21, from the AM1k21/ESP32-CRSF-Relay repository on GitHub, published under the MIT licence. It is a 2-layer board with 4 parts on 11 nets, routed with 47 tracks and 0 vias.

It is built around the SN74HC125DR(LX). Its parts include 2 connectors, 1 capacitor and 1 IC. It belongs with the radio and wireless and home automation and IoT boards of this library.

Main components

1

README

README.md

ESP32-CRSF-Relay

Platform Language License

A high-performance CRSF Relay Node that extends the range of your radio link by forwarding CRSF packets from an ELRS Receiver to a high-power TX Module.

🚀 Key Capabilities

  • CRSF frames forwarding Forwards frames from receiver to transmitter to further range of radio link
  • Dual-Core Architecture: Radio logic runs exclusively on Core 1 (High Priority) to ensure 0% packet loss, while WiFi runs on Core 0.
  • WiFi Manager: Integrated web dashboard at 192.168.4.1 (No app required).
  • Live Telemetry: Real-time scrolling graph of RSSI and Link Quality to visualize signal health and live channel values streaming.
  • Safety Limiter: Adjustable throttle scaling (0-100%) via the web interface—perfect for training beginners without reprogramming the radio.
  • Smart Status: Instantly diagnoses connection issues (e.g., "RC LOST", "MODULE OFF", "DRONE LOST").

🛠️ Hardware Required

  • Microcontroller: ESP32 DevKit V1 (or compatible WROOM-32 board).
  • Input Receiver: Any ELRS Receiver (EP1, EP2, RP1) configured to output CRSF.
  • Output Module: A ELRS-compatible TX Module (I used Emax Aeris Link Nano), or an ELRS receiver flashed as TX.
  • Custom PCB: Required to convert the ESP32's Full-Duplex UART to the Module's Half-Duplex signal. (Not needed if you are using RX as TX, since it has separate UART RX and TX pins)

Wiring

I am using an ELRS receiver connected to a UART of ESP32, another ESPs UART is connected to a custom PCB, and from PCB to transmitter one half-duplex line, as seen on this diagram:

Untitled Diagram drawio
ComponentESP32 PinFunctionNotes
Receiver TXGPIO 33InputConnect to RX pad of ELRS Receiver
Receiver RXGPIO 32OutputConnect to TX pad of ELRS Receiver
Module RXGPIO 17TX DataConnects to PCB Data Line
Module TXGPIO 16RX DataConnects to PCB Data Line
Buffer ENGPIO 25DirectionControls Half-Duplex switching

⚡ Important Power Warning

⚠️ DO NOT power high-output modules directly from the ESP32.

If you are using high-power modules like the Emax Aeris, they can draw significant current (up to 2A at 1W+).

  • Low Power (10mW - 250mW): May work on USB power, but not recommended.
  • High Power (500mW - 1000mW+): You MUST use an external 2S Battery (5-21V) connected to the module's XT30 port[cite: 47, 94]. Failure to do so will cause brownouts and failsafes.

📱 Usage (Web Dashboard)

Once powered on, the ESP32 will broadcast a WiFi network.

  1. Connect: Join the WiFi network Comm_Relay_Manager (No password).
  2. Dashboard: Open your browser and navigate to http://192.168.4.1.
  3. Controls:
    • Dashboard Tab: View live stats, signal graphs, and channel movements.
    • Limits Tab: Adjust the "Max Throttle" slider to limit the output of Channel 3 for training purposes.

📂 PCB Design

The PCB folder contains KiCad project files for the Half-Duplex Translator.

  • Why is this needed? ESP32 UARTs use two separate wires (TX and RX). Most RC Modules use a single shared wire for both sending commands and receiving telemetry. This PCB uses a buffer chip to merge these signals safely.

📚 Technical Docs (MkDocs)

A fully structured documentation site is now available in the docs folder and configured by mkdocs.yml.

Run locally

powershell
pip install -r requirements-docs.txt
mkdocs serve

Then open: http://127.0.0.1:8000

Build static site

powershell
mkdocs build

Parts

4
QtyValueFootprintReferences
1CCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC1
1Conn_01x02_PinConnector_Wire:SolderWire-0.1sqmm_1x02_P3.6mm_D0.4mm_OD1mm_ReliefJ2
1Conn_01x05Connector_Wire:SolderWire-0.1sqmm_1x05_P3.6mm_D0.4mm_OD1mm_ReliefJ3
1SN74HC125DRSN74HC125DR:SOIC127P600X175-14NIC1

Similar boards

  • 2 layers56.5 × 64.8 mmComputationalPrototype, the printed circuit board in 3D

    ComputationalPrototype

    UCHIC/CIWS-WM-Node

    Hardware and software for a smart water meter computational node

    57 parts1BSD-3-Clause
  • 2 layers18.5 × 26 mm24g2usb rp2350zero, the printed circuit board in 3D

    24g2usb rp2350zero

    joypad-ai/joypad-os

    Universal controller firmware for building adapters, dongles, and custom controllers.

    4 parts1.7kApache-2.0
  • 2 layers116 × 33 mm966595-1 and 963356-1, the printed circuit board in 3D

    966595-1 and 963356-1

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    4 parts1.2k
  • 2 layers19 × 18 mmDaughter board, the printed circuit board in 3D

    Daughter board

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    4 parts915
  • 2 layers24.8 × 24.8 mmNrf24 breakout, the printed circuit board in 3D

    Nrf24 breakout

    tardate/LittleArduinoProjects

    a collection of "Little Electronic & Arduino Projects", most involving electronics or an Arduino in one way or another!

    4 parts803MIT
  • 2 layers26 × 20 mmCap chain, the printed circuit board in 3D

    Cap chain

    drandyhaas/KiCadRoutingTools

    A set of Python/Rust tools to aid routing in KiCad

    4 parts744MIT

Questions

What parts does the Halfduplextranslator use?

4 parts, built around the SN74HC125DR(LX). The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Halfduplextranslator KiCad files?

From the AM1k21/ESP32-CRSF-Relay repository on GitHub, at the commit this page was made from: the board is PCB/halfduplextranslator.kicad_pcb and its schematic PCB/halfduplextranslator.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Halfduplextranslator design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).