Skip to the content
2 layers72.9 × 25.4 mmBeepSensors, the printed circuit board in 3D

GPS, IMU, MAG, BARO, and Buzzer for the BeepBerry

Size
72.9 × 25.4 mm
Copper layers
2
Thickness
1.6 mm
Parts
19
Nets
27
Pads
77
Tracks, vias
160, 22
Pours
3
Routed
Yes
KiCad
KiCad 7 (file 20230620)
Created
10 Jul 2023
Updated
6 Aug 2023

Overview

BeepSensors is an open-source printed circuit board by 57Bravo, from the 57Bravo/BeepSensors repository on GitHub. It is a 2-layer board of 72.9 × 25.4 mm with 19 parts on 27 nets, routed with 160 tracks and 22 vias.

It is built around the MAX-7Q-0, BMP388 and BMX160, with the CBT-09427-SMT-TR and CONUFL001-SMD-T among its other parts. Its parts include 4 ICs, 3 connectors, 2 capacitors and 2 resistors. It belongs with the radio and wireless and sensors and measurement boards of this library.

Main components

5

README

README.md

BeepBerry Sensors Carrier

Integrates UBlox GPS, IMU/MAG, BARO, and buzzer.

REV: - was built and verified on a BeepBerry, however, there are some problems with it:

  • During integration, I blew the TPS61030 boost converter IC. I ordered a couple from Mouser and was able to replace it, fixing the device. I was not able to identify what caused the failure in that IC though.
  • The buzzer isn't very loud, but can be used as a generic audio device. It's kind of neat that you can use espeak to do text to speech on such a small piezo.
  • The GPS antenna doesn't have a large enough ground plane, so 3D fixes break often. It's still usable, just not what you'd expect from a UBlox devkit.
  • GPS acquisition eats the battery, but you can control the GPS reset line to disable it to save power.

media/populated_board.png

media/board_installed.gif

media/close_up.gif

media/sensor_addon.gif

Using the buzzer

Simple Tones

text
import RPi.GPIO as GPIO
import time
import random

GPIO.setmode(GPIO.BCM)
GPIO.setup(13, GPIO.OUT)

pwm = GPIO.PWM(13, 57)
pwm.start(10)

for i in range(random.randint(0,10)):
  pwm.ChangeFrequency(random.randint(1,10000))
  time.sleep(random.random())
pwm.stop()

ALSA

In /boot/config.txt, add:

text
dtoverlay=audremap,enable_jack=on
dtoverlay=pwm-2chan,pin2=13,func2=4

then use anything that uses a sound card, IE:

espeak "SAY SOMETHING"

aplay "some.wav"

Using GPS PPS

In /boot/config.txt, add:

dtoverlay=pps-gpio,gpiopin=16

This will allow you to use gpsd with /dev/pps0.

Parts

19
QtyValueFootprintReferences
6LOGOLOGOG***, G***, G***, G***, G***, G***
2100nCapacitor_SMD:C_0603_1608MetricC1, C2
24.7kResistor_SMD:R_0603_1608MetricR3, R4
2Conn_01x10_PinConnector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_VerticalJ1, J2
1BMP3881_project:PQFN50P200X200X80-10NU3
1BMX1601_project:PQFN50P250X300X100-14NU2
1CBT-09427-SMT1_project:CUI_CBT-09427-SMTBUZZER1
1CONUFL001-SMD-T1_project:LINX_CONUFL001-SMD-TJ3
1GPS_ANT1_project:gps_antU4
1MAX-71_project:GPS18P-SMD-1.1-10X9.6MMU1

The 18 most common of 19 parts.

Similar boards

  • 4 layers31 × 100 mmKp ptr, the printed circuit board in 3D

    Kp ptr

    PTR-projects/PTR_mega_hardware

    Welcome to the KPPTR-hardware repository! This repository contains the design files for the hardware components used in the KPPTR project.

    208 parts3MIT
  • 2 layers93.8 × 73.5 mmSimplerFlightV2, the printed circuit board in 3D

    SimplerFlightV2

    elenajusto/SimplerFlightV2

    PCB for team rocket air brakes. (Never manufactured).

    114 parts
  • 4 layers90.2 × 95.9 mmMainboard v04, the printed circuit board in 3D

    Mainboard v04

    pycubed/hardware

    Pycubed PC104 layout design files

    201 parts97
  • 4 layers40.1 × 38.1 mmCrazyflie contol board, the printed circuit board in 3D

    Crazyflie contol board

    sPyOpenSource/ESP32-PCB

    PCB boards designed with ESP32

    98 parts8MIT
  • 4 layers90.2 × 95.9 mmMainboard v05, the printed circuit board in 3D

    Mainboard v05

    alxklso/ISP-cubesat

    This is the repo for the Isomer Space Program (ISP) 1U CoyoteSat CubeSat mission.

    255 parts1MIT
  • 4 layers90 × 70 mmRobot hub rev3, the printed circuit board in 3D

    Robot hub rev3

    dustin-lehmann/TWIPR

    See https://github.com/dustin-lehmann/TWIPR/wiki for descriptions on how to use the hardware and software

    278 parts1
  • 2 layers55.6 × 48.8 mmAAquad PCB, the printed circuit board in 3D

    AAquad PCB

    Fberbari/AAQuad-Evolution

    An original, "from scratch" quadcopter flight computer that was my favorite pet project for some time. Used it to learn all about flight and embedded development.

    47 parts1MIT

Questions

How big is the BeepSensors PCB?

It measures 72.9 × 25.4 mm and has 2 copper layers, 1.6 mm thick.

What parts does the BeepSensors use?

19 parts, built around the MAX-7Q-0, BMP388, BMX160 and CBT-09427-SMT-TR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the BeepSensors KiCad files?

From the 57Bravo/BeepSensors repository on GitHub, at the commit this page was made from: the board is pcb/beepsensors/beepsensors.kicad_pcb and its schematic pcb/beepsensors/beepsensors.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the BeepSensors design in my own project?

Its repository states no licence, so its author keeps all rights: ask 57Bravo before reusing the design.