
ZArduino
zmaker/arduino_cookbook
gli sketch del nuovo progetto Arduino Cookbook e dei video di YouTube

Wireless Neo Geo controller
SNESReceiver is an open-source printed circuit board by 0xe1f, from the 0xe1f/NeoGeoWireless repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 22 × 36.5 mm with 8 parts on 27 nets, routed with 67 tracks and 1 via.
It is built around the ATMEGA328P-PU. Its parts include 3 capacitors, 2 connectors, 1 resistor, 1 IC and 1 diode. It belongs with the AVR (ATmega, ATtiny) boards of this library.
NeoGeoWireless is a wireless Neo Geo controller, built on top of a cheap
aftermarket 2.4 GHz SNES Controller.
It works by converting the SNES controller signals (that would normally go to
the SNES) to format compatible with Neo-Geo, in the process adding features,
like Turbo and Macro button support.
2.4GHz SNES Controller
3x 0.1uF Capacitors
LED (to display turbo status)
Atmega328P
Neo-Geo controller DIN connector, hopefully cannibalized from NG Controller
extension cords
Custom PCB schematics for the receiver add-on board
(KiCad, PDF)
3D-printed case (slightly roomier version for prototyping)
Firmware for the Atmega328P (make writefuses && make install)





Copyright 2021-2024, Akop Karapetyan
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 0.1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C3 |
| 1 | 68ohm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | ATmega328P-PU | Package_DIP:DIP-28_W7.62mm | U1 |
| 1 | GRN LED | LED_THT:LED_Rectangular_W3.0mm_H2.0mm | D1 |
| 1 | NG_Conn | Connector_PinHeader_2.54mm:PinHeader_1x13_P2.54mm_Vertical | J2 |
| 1 | SNES_Conn_1 | NGWireless:Wide5PinConnector | J1 |

zmaker/arduino_cookbook
gli sketch del nuovo progetto Arduino Cookbook e dei video di YouTube

coseyfannitutti/discipad
17-key numpad assembled with only through hole components, including usb type-c

matthewcieplak/super-sixteen
Code and schematics for the Super Sixteen Eurorack sequencer

coseyfannitutti/romeo
Staggered 40% keyboard pcb that can be assembled with only through hole components, including USB Type-C

mattybrad/drumkid
Version 4 was the first successful working design, with full code, schematics, Gerbers, etc available on GitHub.


leomil72/LM80C
A Z80-based homebrew computer withTMS9918, AY-3-8910, Z80 CTC, Z80 PIO, and Z80 SIO

It measures 22 × 36.5 mm and has 2 copper layers, 1.6 mm thick.
8 parts, built around the ATMEGA328P-PU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the 0xe1f/NeoGeoWireless repository on GitHub, at the commit this page was made from: the board is schematics/rx-snes/SNESReceiver.kicad_pcb and its schematic schematics/rx-snes/SNESReceiver.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).